KMA3700 Accu-Cut XL - Universal Track Saw Guide System - Make Straight, Cross, Rip & Angled Cuts Easily

I am not a carpenter. I don't make things to sell, so I have no basis to judge this in terms of a professional. But for someone who can't rip straight with a circular saw, and is slightly afraid of a table saw, this was the perfect solution. I needed to rip several 4x8 sheets of plywood into 3" strips. This was the exact right set up. Instructions are good. Easy to follow. My amateur Ryobi circular saw fit into the guide and off we went. Very pleased with this purchase

Makes cutting full sheets of plywood easier and eliminates the need for expensive table saw

Pretty good. Can use some Drawer tape to get the slide to snug-up to the rails, once this is done you get VERY straight cuts. YouTube Videos are out there showing the process. Trimmed out windows with it, zero gaps. Would recommend.

I just put these together a few days ago, got it dialed in and did a trial cut on a piece of 3/4 inch exterior OSB. I believe this is going to be a big help in making better and more precise cuts in remodeling and beyond. Heck, I may start building furniture again.

Great track saw attachment

Holy cow! If you don’t have the money for a table saw for large pieces of wood to cut this is a must! We did a huge project that required cutting multiple sheets of breadboard and plywood. This worked like a charm. Granted we are not professionals however, I’m pretty sure this kept our marriage together during this project!😁

I bought this because I couldn’t afford a table saw. But WOW. This is so much safer than fussing around with a sheet of 4’x8’ plywood on the deck of a table saw. It doesn’t fill all the needs so I did eventually get a table saw This is a quality tool. A lot less expensive than a Festool which we used at work. Pretty much just as good. So get it. Get enough pieces to do the work. Label the underside of each. Find a create a safe place while not in use. I paired it with a Makita 8” radial saw. And a really nice blade.

I recently used this to install hardwood stair treads and risers. I use a razor knife to mark cut lines for treads and risers as it is far more precise than a pencil line. With this track combined with my DeWalt cordless saw I was able to make perfectly accurate cuts on my razor cut line. Also made short work of breaking down a couple sheets of maple plywood for some built in shelves. I can see I wont be using my jobsite table saw nearly as much anymore. If you already have a cordless saw then this is a super cheap way to get into a track saw set up. I've used DeWalt's track saw a few times and Festool's several times and I can say that this is just as accurate. The only thing missing here is good dust collection but at this price point it really is a non issue. If you've been wanting a track saw but didn't want to spend the 500-700 dollars for the name brands this set up does the same thing at a fraction of the cost. I highly recommend!

Had quite a few 4 x 8 ft sheets of OSB to cut up, and this made it much easier and a lot more accurate. My Evolution circular saw fitted perfectly. Nice and easy to set up and use.

Rectifico que si trae la mica y por eso le doy 5 estrellas

Super produit très utiles et rapide à monter expédition plus vite que prévue content en tout je le recommande

Very happy with product and it's ability to ensure perfect cuts with a circular saw. My one complaint would be that the set screws holding the track together come loose very easy. They are Philips head and are small and difficult to tighten. Would be much better if they were Allen Screws.

Some assembly required. I was surprised at the care required to assemble this tool, for a straight edge. Make sure you have a 4 ft straight edge to use when assembling. (Read the instructions carefully!) The 8' tool worked well for my countertop cutting project. Lines were straight and cut widths were as accurate as I can measure. I see some people have complained about the AccuCut creeping while cutting. I find that I need to keep the tool and material I am cutting clean while I am using it. I vacuum the tool and the workpiece between each cut to keep the tool gripping the workpiece. Storage is an issue, so I needed to break down the tool into 4' sections for storage and I wish there was a 4' tool bag/box to store & transport the AccuCut XL. I may have to fabricate a tool box for it to keep everything together & keep it straight for long life. Note.. you will want to set it up for (1) one saw, and always use that saw with the tool, because part of the setup trims 1/8" of the blue edge with the saw blade. The blue edges are replaceable, but I don't want to do that too often.