JooFn 5 Pairs Anti-Slip Brake Handle Silicone Sleeve Mountain Road Bike Dead Fly Universal Type Brake Lever Protection Cover

Been using these for over two years now on a Yeti SB5+ and a Sur-Ron X. Also installed a pair on a friend's Yeti. They greatly increase lever grip and control and have had no issues; no slippage or deterioration. Highly recommended.

These grips work well, fit tightly and insulate the hands from the brake lever in cold weather. Several reviews stated the grips were tough to get on the brake lever. I found that to be true. I also found out after putting on one of the grips that there is a trick to help put the grips on. This helped me and hopefully it can help you as well. 1) Soak the grips in hot water first. This expands the silicone and the opening. 2) Remove the grips from the water. Empty the water in the grips. 3) Place a drop or two of dish soap at the grip opening and rub the soap 360 degrees around the opening. Then fill the grip with some hot water, about half-way full. Then put your finger over the opening and shake the water in the grip so that it contacts the soap. Shake the grip well. This provides a soapy film on the inner wall of the grip and lubricates the inside wall when sliding the grip on the brake lever. Empty the soapy water inside the grip and dry off the outside. 4) Get a dry paper towel and double it over. You are going to use this to slide the grip on the lever. 5) While the grips are still warm, push the grip onto the brake lever with your bare fingers, aligning it as you go. You will probably be able to push the grip on anywhere from 1/4 inch to 3/4 inch, depending how strong your hands are and how much the silicone opening expanded and how warm the silicone is. 6) Here is the trick. Take the folded dry paper towel and tightly hold the outside of the silicone grip with the paper towel seated in your palm and fingers. The dry paper towel provides your palm and fingers additional friction against the silicone and makes it easier to push-pull the grip on. 7) Start pushing the grip on from the bottom of the brake lever. Then firmly slide your fingers up the lever, and you will begin to pull the grip on via the friction provided by the paper towel. Pull the grip all the way to the point where it resides on the lever. 8. Repeat this motion, starting from the bottom and proceeding to the top of where the grip is on the lever. 9. You will move the grip up the lever with each iteration and find that you are pushing the grip on at the beginning (bottom of the lever) and transitioning to pushing/pulling the grip on (probably half way up the length of the seated grip to the end of the seated grip). Continue until the grip is fully seated. It took me about a minute or two to install each grip when applying these steps. 10. The bottom line is that the inside wall of the grip has been lubricated to DECREASE friction and the outside wall of the grip is 'wrapped' in a dry paper towel to INCREASE the friction when gripping the silicone. The physics of this makes it much easier to slide/push-pull the grips on vs trying to push a non-heated and non-lubricated grip on with your bare fingers.

Great deal great colors

Good quality fair price. Was shorted a pair of black sleeves

These are great. I put them on my electric scooter and I love the covers because they add grip but also keep the brake levers at a comfortable temperature in the hot summer heat or in the cold. Tip: Get a spray bottle and add water and 20% of that with alcohol. Or use eyeglass cleaner and spray the brake levers and put 2-3 sprays inside the grip and push them onto the levers and corkscrew them on. I got mine on in less than a minute with this technique. The alcohol will evaporate and the water will squeeze out. To remove these you will either have to fight it, or stick a nozzle from the air compressor in it to blow it up like a balloon as you slide it off or what I will probably do is cut them off when I want to or need to change them.

It is a hassle to put on but if you use a little WD40 and spray inside the silicone lever cover before installment it slides right on.

Great way to add color and comfort to brake handles. Great quality and easy install

Adds a soft touch to the brake levers. Use a few drops of rubbing alcohol in the sleeve and should slide right on.