Clear Ice Cube Tray for Whiskey: FDDBI 2Inch Clear Ice Cube Maker - Silicone Large Ice Cube Tray - Square Ice Tray for Bourbon Old Fashioned Whisky

This tray works as-advertised. Super easy! I finally stopped using the old igloo cooler and mallet. Consistently good clear cubes. Follow the directions and dial in the perfect time to pull them out of the freezer and you’ll be happy. Since my purchase date, the plastic tray cracked in a couple of places. I reached out and the replaced it immediately! I was just hoping to buy the part. GREAT SERVICE!

It took me 1 practice attempt to figure out what works for me. The mold works great. Great quality, nice to have 8 cubes at a time. If you let the tray sit for a little before removing cubes you should be fine with no difficulty. Usually start to see the ice melt after 2 drinks. Very happy with the purchase.

Easy to use and actually gives you clear ice cubes. You can tell this was well made and will last a long time. Great value

This clear ice maker works very well and makes nice, clear ice. The only downside is that it takes up quite a bit of room in the freezer. Overall, very happy with it.

I've always loved the large, clear ice cubes served at high-end bars and restaurants, so I purchased this kit to try to make them at home. This kit really does produce amazing, clear ice cubes! Once you get the hang of it, it is very easy to use. For some reason, the first time I used it, I had a difficult time removing the ice cubes from the silicone tray. However, they came out much easier after the first time using it. This kit is great for making cocktail ice cubes for parties, and friends have all commented on how much they love my ice cubes! One word of caution - since this kit uses directional freezing to make the clear ice cubes, it takes approx. 36 hours to make one batch of cubes, so I would make them ahead of time and seal them in ziplock bags if you will be making a lot of drinks.

Hmmm... Well, it made good cubes. And it does make (relatively) clear cubes. However, for some reason, the last 3 batches have had 1-3 center cubes that seem to siphon water to the middle {those are the affected cubes) and I end up with 1-3 HUGE cubes and the others are all smaller. I have no idea what's causing this or how to stop it. As "problems" go, it's a minor issue but it's still a little annoying.

This works well if you fill it right. You can’t fill the tray all the way up or it leaks out, leave a little space in each cube and it works well. The ice is not crystal clear in my freezer (using distilled water) but it’s miles better than refrigerator ice.

Does it make clear ice? Yes. I can't fault it for that. However: It does not come with any paper instructions or documentation. You only have the 4 step instructions in the product description. The first step calls you to "fill with water". However it does not specify an amount of water, and there is no fill line. You just have to guess, and you will find out if you put to much water when you get to step 2 "place the plastic silicone mold". The water will overflow from every orifice of the product. There is no indicator for how frozen the ice is. Again you just have to guess. You will probably make the mistake where you thought it was done, start to remove the silicone sleeve (which is a pain to get out), and water gets everywhere. I don't see this product being durable enough to withstand average use. This is going to remain at the back of my freezer as a novelty for when I have guests over, unless I return it. Also, the clear plastic top does not fit well.

Does exactly as it says. Foam outside does get pushed out when freezing from the ice but the final results are unreal. Follow the instructions and wait the time. Ended up buying 9 for all my shareholders.

As advertised. I've done one batch so far and I am very happy! It was a little bit tricky understand how to remove the silicone form because I did not want to break anything by pulling in the wrong direction. I let it stay for 5-10minutes and then I could lift the plastic tray up that contained the silicon tray. Basically it is only attached to the ice below the tray by the small piece of ice in the hole beneath the ice cubes. I took mine out after ~30h and they were mostly clear! There were some bubbles trapped and I might have cause scratches on some, but they should look very nice in a glass with something to drink. It was just one cube in the middle that for some reason rose above the others and got cloudy at the top, could have been med handling the tray getting into the fridge. The bottom tray ice didn't look to bad either but it wasn't fully frozen when I picked it up, potentially if it stays longer it could be used for some fun sculpting, or just hack it up in smaller pieces. I choose this clear ice maker because of the lid. I noticed that other open silicon molds picked up a scent from the fridge after a while, and that transferred to the cubes. This was helped by putting the silicon molds in the oven at 120C for a while but the cover should help with not getting the smell in the first place. Took some three weeks to get to Sweden. For the price this is perfect, I am very happy!

Description says it takes 24-30 hours, the box says 36-48 hours. It's taken minimum 48 hours so far. If you pull it out before it's frozen you've wasted 2 whole days. Some instructions would have been helpful as I'm just guessing as I go along which is annoying. I am yet to get a batch of perfect ice, however the space that should have the cloudy excess has some very clear ice which with an ice pick would be great to use.

Simply put, the ice is not clear!

Poco practico no es fácil ni rápido extraer los hielos