KSP Diff Drop, CNC Machined T6 Aircraft Billet Aluminum Differential Drop kit with skid plate drop spacer fit for Tacoma 4Runner 4WD

The installation was pretty easy, no real instructions, but it's pretty obvious though. However, while it came with two bolts that were longer to allow the skid plate to reach after the spacers were put in. But, it needs two more longer bolts for the back skid plate. It isn't a deal breaker, but it was kinda annoying to have to go get one. You also need two more spacers, or, 4 larger nuts to go over the bolts to make a spacer. I wish I had pictures, but didn't think about it until I was finished with the installation.

I installed this drop kit in less than 10 minutes 22mm socket 19mm wrench for old hardware Then will need 22mm socket and 7/8 wrench to install This kit cost only $20 and it’ll save you $$$ by putting less stress in front differential of Tacoma 4x4

Worked as described

Decent quality kit. I used this to fix a small driveline noise after having lifted the truck 2 inches. Pros: -quick easy install roughly 30min -spacers are aluminum anodized in black (matches other underside parts) & won't rust Con's: -not enough washers. There's 2 washers which are I'm assuming for the larger differential bolts. But no washers supplied for the skid plate bolts which could almost slip through the skid plate openings without them. The factory skid plate bolts have large washers attached so II couldn't reuse those. I had to get my own. - no instructions, but there are plenty of online threads with pictures and videos Overall would recommend them to others but have to get your own skid plate washers.

Shop installed this with my lift, no vibration with this kit!

Good product, the package will come with diff drop spacers, skid plate spacers, long bolts and nuts. However it will need the following. You will need longer bolts and washers for the rear part of the differential skid plate. You can use the stock bolts but the skid plate will hit against the differential. You will also need longer bolts and washers for the back of the oil pan skid plate, because since adding the 1 inch spacer for the differential, it created a gap for the rear of the oil pan skid plate. I'll have to double check but I think the bolt threads for this is M8x1.25. What ever the stock bolts are, add either 1/2 to 1 inch of total length and add washers for spacing and get it at any hardware store. Update: I bought M8x1.25 x 40mm bolts for the rear oil pan skid plates and used a large nut as a spacer. The nut doesn't need to thread to the bolt. The rear of the diff skid plate i used M8x1.25 x 30mm plus washers.

Era lo que pedí yego en el tiempo que esperaba

Does not align properly and the provided washers are too small. You will have to drill the skid plate holes to align it and bolt it in. Bad customer support too, and unable to return without a shipping fee.

Fits my 2003 toyota 4runner. After install, not much of a difference in the axle angle (3inch lift) but better than having full stress on the lifted axle.

Just installed this kit. 1. Main bolts that hold the diff up are marginally long enough. If I used the washer provided the threads would not protrude the nut! So the nylock bolt would be of no use unless you omit the washer. 2. The smaller spacers provided to shim the skid plate down are of no use. They are approx 1/4” thick. You need a spacer that should be the same thickness as the large spacers. 3. There were NO instructions in the kit. Not a problem for me but for some it may be an issue. 4. You will no longer be able to use the jack point on the skid plate as the kit spaces it away and provides no shim or suggestion to fill the space. Instructions or a mention of this on the sale page would have been nice! .....so I am now unable to run my skid plate till I get shims/washers to take up the space. I do not recommend this kit, to anyone. If it was in its allowable return timeframe, it would be returned!

I waited for this for almost a year and never showed up, ended up buying bolts and washers from my local hardware store instead, cheaper and works well