Faucet Diverter Valve with Aerator, 3-Way Diverter Valve for Hand Held Shower, Sink Faucet Splitter for Kitchen and Bathroom, with 55/64'', 15/16'', G1/2” Adapters

I was replacing a broken valve and this is junk. I put it on and it broke off like the peace literally broke off. That goes around the sink. I mean, how do you make junk like this waste of my time? I've been waiting. I'm waiting for this part.

I use this faucet diverter to route water from my kitchen sink to a reverse osmosis (RO) system. I’ve purchased it twice. The first one eventually leaked, the second has been running for over a year with daily use and no issues. The difference wasn’t the product, it was how I was using it. RO systems create more resistance than typical faucet attachments. Running this diverter at full blast puts unnecessary pressure on the seals. With the replacement, I stopped opening the faucet all the way and used a moderate flow rate. Since then, it’s been completely leak-free. A few practical notes from real use: • Use plumber’s tape on the threads. This is essential to prevent drips. • Snug is good, overtightening is not. • If you’re feeding an RO system, don’t run the faucet wide open. Lower flow reduces pressure and extends the life of the diverter. I like that this allows me to switch between normal sink use and filtered water without making permanent plumbing changes. It’s compact, affordable, and easy to install if you take a minute to do it properly. Minor cons: • Not designed for sustained high-pressure flow • Requires correct installation and reasonable water pressure Overall, this has worked very well once installed and used correctly. The current one has been reliable for over a year, and I would buy it again for the same setup.

I’ve had it about a year and no real issues, sometimes it leaks a little but usually it’s because it’s become loose, as I’ve got like a sprayer hose attached to it so it might cause it to twist a little over time with constant moving. I tighten it back up and it’s golden.

This sucks the gasket blows out after about ten uses and sprays water all over.

We have a beautiful shower with all kinds of nobs and dials and multiple settings. Hand held, waterfall, rain, mist, spray and faucet -- plus it times your shower and tells you the water temp. It looks great and wife lives it. The handheld broke inside the shower unit. Everything else is working. I picked this up to "Frankenstein" the shower unit to plug the hand-held shower "wand" in to the faucet. It's not pretty, but it works. At a very reasonable price. That shower want takes about 2-3 mins off my shower time. The vinyl tape made sure there were no leaks and while the pressure is a bit lower plugged in to the faucet, it's more than acceptable. My only complaint is the threaded adaptor to fit in the faucet fixture was almost too short and I had to be very careful not to strip the threads -- removed one star for that. Note: This is not a permanent fix for us -- but to carry us over a few months to replace the entire shower unit as I discovered the innards of it were very cheaply made (sad for something that ran us near $600) and I just don't have the time for this type of repair right now. I can easily see this being handy for a tub that has no shower option! I had something similar years ago I added to my apartment tub (which didn't have a shower).

Very delicate item. It will definitely break in few uses

This fits really well and super easy to put on. The valve does its job. It redirects all the flow of water and doesn't lose the water pressure. I have had no leaks.

It fit and was plenty easy to install it just didn’t work the way i had hoped for separate reasons than what have to do anything with this parts design but has good water flow and a quality made piece its just its external attachment didn’t fit the part i wanted it too so that was problem but not one the part had anything to do with

It worked connecting a faucet to a shower head or converting faucet to bidet. I tried so many things and this one only thing worked. I had to use a rubber washer from the original aerator on this connector to the faucet

Well made.

It's good and the sealing is good, keep in mind that your faucet needs to be M22, Otherwise you need an adapter to M22, Also your hose need to be G1/2, otherwise you need an adapter from G1/2 to your hose.

Werkt goed

Husband installed it on our tap and it broke within 2 minutes of use. Need to return. Which is a shame because we waited a couple of weeks for it to arrive.