Evolution Power Tools RAGEBLADE 7-1/4-Inch Multipurpose Cutting Blade for Steel, Aluminum, Wood and Plastics

At 10 amps this little saw has a lot of power, it took me about an hour just to set up but once set up is all good. Overall, is a powerful saw that can cut through metal with ease. it comes with a general saw blade that cuts wood, plastic and soft metal. I decided to buy an extra saw blade that is specifically for metal use. That way the saw blade will last longer. i was surprised to see package comes with some spare safety glasses, as well as foam ear plugs as the machine is quite loud while in use. Safety Glasses and ear plugs was a good attention to detail. Overall this is a great little machine, however when using most important is you secure whatever you are cutting well, from the front end and the back end, because if not the item you are cutting can fly out. It happened to me, lesson learned. It performs nice straight cuts, so I'm happy with this purchase.

Excellent performance- can’t believe how easily this cuts brass, copper, and aluminum stock, and does well even with mild steel. Extremely good quality, esp. given very reasonable price point. Good safety guard. Does throw chips- so wear eye or pref full face protection. Not a complaint- just a fact!

Works as expected. Direct replacement for my rage saw. First cuts on 1” square steel. Other cuts on 3/16 steel and 1 5/8 round tube steel. I hook my shop vac to the saw but it still make quite a lot of metal chips to clean up. Definitely will buy again

I needed a small saw to do 90s and 45s for my smaller steel stock (2 inches and below), I have a plasma cutter for bigger stuff. First off its only ~$120 so you can’t beat the price and even with the general purpose blade it cut 1x1x16GA square tube (at 45) like a hot knife through butter. I also did 1x1x11GA nice and slow, with minimal sparks. I did also buy the stainless steel, 48 tooth blade and noticed it did cut just a little bit cleaner. I'm expecting that the official steel blade would out last the general purpose blade due to the number of teeth etc. In either case I could probably take that cut steel and jump right to welding w/o any sanding prep. The weight and size are perfect for small home shops like mine. There were some minor issues with the saw, I hate the stupid locking chain, they have me one ear plug (really minor but wtf), and the rubber foot for the clamp was a pain to put in (why did I have to do it)? The only real issues I have are: #1 This is saw has a 20MM (METRIC) ARBOR. I read some of the comments and they lead you to believe you can run this saw with 5/8s blades w/o a bushing, NOT TRUE! You need to get the ‘Evolution CSBUSH20M5/8 bushing’. Amazon sells it and it’s cheap. You cannot find 7 ¼ inch 20MM arbor blades in stock at Home Depot or Lowes, you have to order them. So you may want the bushing in case of an emergency. I don’t see this as a huge deal, just something I wish was called out. #2 I found that the clamp system alters the angle you set for making 45s etc. I've seen mush more expensive saws with the same design so its not just this saw. I'm doing my stuff with clamps now. #3 The hash marks for 45 are off by a couple of degrees. I made my own new hash marks (hey its ~$120) I’m very happy with the saw so far. PIC INFO: The cut steel pics are 1x1x16GA from the official steel blade the general purpose blade cut very similar to so I didn't post the pic. I put a blue 5/8s arbor blade on the stem so you can see the fitting problem. I have not ordered the bushing yet so I can't say how well that works. Btw it does have a small dust port you can install and it comes with eye protection and spare motor brushes.

This is a very good blade that goes well with their (admittedly) cheap metal saw. it worked great and lasted quite a while. After it dulled down a bit, I sent it out to be sharpened. While it was gone, I bought an upgraded Rage metal-cutting blade (with twice as many carbide teeth). That one also worked great, but after about 15 minutes of use, my saw quit working. I discovered the brushes in the motor were shot. I replaced them with the spare set that came with the saw. These were also done after another 15 minutes of use. By the time I got the brushes replaced again, the original blade was back from sharpening. I reinstalled it, and no more brush problems.I think all that extra carbide was putting a load on the saw motor it wasn't designed for. This blade is perfect for the saw; you can't improve on it.

Appareil de moyenne qualité, lame a peu de durée ( dans mon cas 20 coupes). Ne forcer surtout pas la scie, le moteur est sous alimenté, les brosses se sont détruites après quelques usages ( ils en fournissent un ensemble d'extra, je me demande pas pourquoi???). Les instruction sont assez claires mais les photos vous montre que l'on peut couper un tube a plat ce qui est contraire aux instructions!!! Cela va diminuer rapidement la durée de votre lame . Coupe en 45 pas trop précise, l’étau glisse. J'ai malheureusement dépassé ma date de retour. Saw of average quality, Blade have a shorter life (in my case 20 cuts in .125'' thick) Do not force the saw, the motor in under powered, brush were destroyed after a few utilisation( they supply you with extras, I wonder why?)Instruction are clear but photos indicate contrary like cutting tubing on the flat, wich will reduce life of the blade. 45 cut is so so, vise let the piece move. Unfortunately miss return date. But after review, they sent me another saw... what a différence. KOODO'S to them. Good after sale service.

Excelente producto muy satisfecho

ES UN DISCO MUY BUENO LO HE ESTADO UTILIZANDO OARA CORTAR MDF Y DEL TIEMPO QUE LO ADQUIRÍ HASTA EL DIA DE HOY SIGUE FUNCIONANDO MUY BIEN

Corta muy bien muchos materiales, pero una de más dientes cortaría más fino, o bien usar con muchas revoluciones

Corta fácilmente los metales de 18 mm y ángulos hasta varillas de 5/8 esperemos cuanto le dura el filo al disco