Youmile CNC Shield V3.0 Expansion Board Kit With Board for Arduino, 4PCS DRV8825 Stepper Motor Driver and Heatsink, 10PCS Jumper Cap, USB Cable For Engraving Machine

Everything you need to run GRBL. Does a fine job on my home built laser cutter. Good value for money.

4 drivers, an Arduino uno and the CNC shield all for less than I once paid for an Arduino on its own.

Purchased to drive a modified Proxxon MF 70 mill #1 The clone V3 Uno board is good and functions as expected. The board has the ICSP header pins soldered on which contact the base of the shield board when it is fitted, some actually touch some of the end stop pads on the base of the shield. The ICSP header shouldn't have been fitted for this application so was removed. #2 The CNC shield has a few minor issues. The header pins are soldered and the joints are good but one set was about 5 degrees off of vertical and the other closer to 15 which required desoldering and refitting before use. Given this fail in very basic QA I went through the board and checked ALL of the joints just to be sure they were good. I don't think that this is something I should have to do but I suspect it would be a problem for some. # 8825 Drivers As yet untested but I am expecting at least one to fail on power up which is not unexpected, failure rate in unbranded steppers can be high. I may change these for a branded alternative that also supports X32 micro stepping. #Overall comments Good value for the price, you could source all of the components for a similar price point but it would be difficult. You do get all you need to drive a small CNC system but you might want different stepper drivers depending on use. A power lead for the Uno is provided which is a nice touch. There is no provided documentation but this is readily available on the internet so a bit of a non-issue. Given that the steppers will get hot and really do need forced air cooling a small fan bundled in would have been nice.

Easy to work with, plenty of tutorials on the web.

I bought this to make a two axis jig on which to mount screens, lenses and a camera module to simulate refraction of the human eye for an R&D project at work. It does what it needs to and I would buy it again. Great price so we can easily afford to keep a few spares just in case.

it appears this is an older version and while working with GRBL the pins for (z) end stop and spindle enable have been swapped round. took me ages to find this out so i thought i’d pass it on😁

The Youmile CNC Shield V3.0 Expansion Board Kit offers a complete solution for small-scale DIY CNC projects, including the Arduino Uno board. Here's why it's a solid choice: Comprehensive Components: This kit provides all necessary components except for the stepper motors, such as the CNC shield, DRV8825 stepper motor drivers, heatsinks, jumper caps, USB cable, and Arduino Uno board, ensuring a hassle-free setup process. Sturdy Construction: Each component is crafted with durability in mind, guaranteeing reliable performance for your CNC project. Versatile Compatibility: Designed for Arduino boards, the CNC shield V3.0 expansion board is compatible with various CNC setups, offering flexibility in project design. User-Friendly Setup: Clear instructions and included USB cable simplify the installation process, making it accessible for DIY enthusiasts of all skill levels. While the Youmile CNC Shield V3.0 Expansion Board Kit offers an all-inclusive solution for small DIY CNC projects, it's important to note that stepper motors are not included. Nonetheless, it provides everything else needed to set up a functional CNC system, including the Arduino Uno board.

I bought this to build a CNC machine, however when it arrived it was in a bag, so very little protection against damaging the pins on the boards. The CNC shield had a block of foam covering the pins however this foam was full of solder splashes and component croppings. When I removed the foam the pins were all bent, every one had to be straightened. The Shield also had long component legs that hasn’t been cropped so we’re short circuiting to the pins on the arduino board underneath. The sockets on the arduino board were all out of line some sitting higher than others. All in all very disappointing. As I am an electronic engineer and have the right tools available I was able to fix these faults. I genuinely was disappointed in the product. I know it is cheap but that’s no excuse for poor quality.

Sehr fairer Preis mit sogar originalem Arduino UNO

Il Youmile CNC Shield V3.0 Kit è una soluzione completa per trasformare una scheda Arduino in un controller CNC, ideale per applicazioni come macchine per incisione, stampanti 3D e altre attrezzature di automazione. Caratteristiche Principali: Compatibilità: Progettato per funzionare con Arduino Uno, questo shield supporta il firmware GRBL, una piattaforma open-source che converte i comandi G-code in segnali per motori passo-passo. Supporto per 4 Assi: Gestisce fino a quattro assi (X, Y, Z, A), permettendo configurazioni avanzate come la duplicazione degli assi o l'implementazione di un quarto asse completo con firmware personalizzato. Driver per Motori Passo-Passo: Il kit include quattro moduli driver DRV8825, ciascuno dotato di dissipatore di calore, che offrono un controllo preciso dei motori con microstepping fino a 1/32 di passo. Facilità di Installazione: Lo shield si monta direttamente sulla scheda Arduino, con connettori a 4 pin per i motori e jumper per la configurazione del microstepping, semplificando l'assemblaggio e la personalizzazione. Esperienza d'Uso: Ho utilizzato questo kit per assemblare una piccola macchina CNC per incisioni su legno. L'installazione è stata relativamente semplice, grazie alla compatibilità con Arduino Uno e al supporto per GRBL. I driver DRV8825 hanno fornito un controllo fluido dei motori passo-passo, permettendo movimenti precisi e affidabili. Tuttavia, è fondamentale regolare correttamente la corrente dei driver per evitare surriscaldamenti e garantire la longevità dei componenti. Inoltre, l'uso di un alimentatore adeguato è cruciale per il corretto funzionamento del sistema. Pro: Kit completo con tutto il necessario per iniziare. Compatibilità con Arduino Uno e firmware GRBL. Supporto per quattro assi, offrendo flessibilità nelle configurazioni. Driver DRV8825 con microstepping fino a 1/32 di passo. Contro: Richiede competenze di base in elettronica e programmazione per l'installazione e la configurazione. La regolazione della corrente dei driver può essere delicata; un'impostazione errata può causare surriscaldamenti o malfunzionamenti. Non include un alimentatore; è necessario procurarsene uno separatamente, assicurandosi che sia compatibile con le specifiche del sistema. Valutazione: 4 stelle su 5 In conclusione, il Youmile CNC Shield V3.0 Kit rappresenta una soluzione versatile e conveniente per chi desidera realizzare progetti CNC basati su Arduino. Offre un buon equilibrio tra funzionalità e facilità d'uso, pur richiedendo una certa attenzione nella configurazione e nell'assemblaggio.

J'ai commandé ce kit pour une CNC en DIY que je suis entrain de terminer. Je n'utilise pas, pour ma part, les drivers fournis mais des DM542T avec 4 Nema23 3nM. La carte CNC SHield permet facilement de connecter les DM542T. Pour l'instant, je n'ai rien à dire, tout fonctionne parfaitement avec GRBL1.1 sur ma Workbee. Je recommande ce kit, qui peut facilement faire tourner directement 4 nema17 dans sa configuration de base.

問題ありませんでした

Good item