OVERTURE ABS Filament 1.75mm, High Strength & Heat-Resistant 3D Printer Filament, Low Warping, Excellent Durability, ABS 1kg (2.2lbs) Cardboard Spool, High Precision +/- 0.02mm (Black 1-Pack)

My X1Carbon arrived and this was the only plastic I got at the same time. Luckily, I bought 4 kg, because it's awesome. I've run it in "ludicrous mode" and it's fine. I've tweaked some settings, but it prints a good benchy with "generic abs" temp settings 270c hot end and 90c bed. I have a screenshot from the app with whatever settings it shows. Pros: Great bed adhesion, great layer adhesion, minimal shrinkage, clean finish when you use iron mode, strong, solid glow, good price, fast shipping, and durable. My neighbor pulled in with his 1 and 3 year olds and I have them some fidget cubes. They were throwing them on the driveway and jumping on them and nothing broke, but I told him to let me know when it does. Cons. Be careful of supports. This stuff is really extremely hard so tree and grid supports are way too hard to get off with the great layer adhesion. You need a longer carry distance between them so hopefully your printer can do something like a. 7.5 mm+ hollow support since that's been easyish to remove with minimal left on the part. You need pliers to remove them and it's not easy so be careful dudes and dudettes. Unknowns: Deformation temperature, long term glow, how fast it can really print, etc. I haven't printed much for sharp corners yet since it's always safety third. I also haven't acetone vapor smoothing yet, but I will and almost promise to update if it was bad. It does have quite a smell so I'm sure it's toxic and I would put it in the garage. I'm def going to seal my chamber better, but that's not a filament problem with the right ventilation. TLDR; see title. I gave all my printed things away so I only have inappropriate ones or idiot (me) decided to slice it very poorly 🥴

Generally, Overture has great stuff, even for cardboard spools, generally their filament is always on point for me. I print a lot of technical/challenging filaments -- so really any complaints that a civilian might share in a review are never really a concern to me. IE, I'm never going to print with a cardboard spool, I will always respool the thing, and then -- yeah, even PLA I am going to dry. So honestly, and genuinely when I say that this is LITERALLY the best glow in the dark ABS filament that exists, I mean it. 100%. I've bought dozen(s) of spools of this stuff over the coarse of 1-2 years and it's always the same high quality, strong, long lasting, green glow, with literally 0 troubles printing. I kid you not, Bambulabs ABS with their profiles prints worse than this stuff does -- and it's half the price! You can't find better filament for the money. As for tangling and moisture issues, like I said, I'm not in the business of wasting money on filament, so I take the proper steps, it's not a downside to me, it's part of the hobby.

I started enclosing my Ender 3, but after getting three sides up I was impatient and tried this ABS without finishing it. Impatience being the operative word I even printed at faster than PLA speeds and wider than normal line width. I was looking for functional, high strength parts that can withstand dirty water and outdoor environments (Bird bath or pond), and I was not disappointed. Pros: Able to print quickly. High quality, strong, and durable prints. MUCH easier to print than any PETG I have tried. Inexpensive. Very little stringing. No nozzle clogs. Prints without an enclosure (I did shut the register off in the room) Cons: Wife claims she can smell it. My eyes are sensitive, and burn a little if I'm in an enclosed room during printing. Slight warping on elongated parts, though much better than I expected (using draft shield). If using a raft, very hard to remove it. Brim works well. Thin (two or three line widths) vertical parts aren't very strong. Requires all-metal hotend (On an Ender-3 I just replaced the heat-break with a 2-for-$15.00 all-metal heatbreak. https://www.amazon.com/gp/product/B08TCD4M1S Note: My Ender-3 has a 50 watt heater, glass bed, and All-metal heat-break Cura settings: Ender-3 V2 using 0.4mm nozzle Generic ABS Line width: 0.8 Wall line count: 3 Printing temperature: 240C Build plate temperature: 105C Print speed: 80 Enable retraction: ON Retract at Layer Change: ON Retraction Distance: 3.0mm Z hop when extracted: ON Z hop height: 0.4mm Build Plate Adhesion Type: Brim Brim width: 8mm (make sure brim reaches draft shield) Enable draft shield: ON Draft shield X/Y distance: 8mm

I have a fully enclosed printer that uses a Voron V0.1 print head, that is built specifically to print ABS, so I was excited to try this filament. I'd give this a 4.5/5 stars overall, mostly because the settings printed on the side of the spool didn't work for me, so I had to spend some time dialing it in on my own. I initially had a bit of trouble compared to the last brand I tried. Mostly some minor warping on the corners of prints. Increasing the bed temp higher than what it says on the box. I am now using 105c on a PEI bed with some glue stick applied. I'm also using the part fan at 10% (starting at layer 4), as I found it helps a lot with surface quality. With these changes, and chamber temps between 45c and 50c, I'm getting great looking parts without any warping and NO brim! Bridging isn't great, but I probably need to work on the bridge settings in my slicer, since ABS shrinks a lot more than other filaments when cooled. But overall I'm very happy with the results after the changes I made.

Ottimo filamento, stabile, facile da stampare, lascia qualche coda, ma ha un’ottima aderenza tra i layer e un’ottima finitura

El mejor filamento ABS relación calidad / precio, se imprime perfectamente , la calidad es optima, ni mejor ni peor que otras marcas, sabes que no vas a tener problemas de enredos , nudos, sin humedad. Llevo quemados como 20Kg de este ABS en muchos de sus colores.

Très bon filament, s'imprime très facilement pour de l'ABS Je n'ai aucun warping (Creality Ender 3 avec enclosure) Attention, il faut bien sécher le filament, il était bien humide lorsque je l'ai reçu. Après 6h dans le sécheur, il s'imprimait très facilement.

Dopo aver utilizzato per mesi questo filamento in abs, vi lascio qui la mia recensione sperando di esservi di aiuto. 📦PACKING Imballaggio perfetto, ben rifinito e ben curato. Bobina sigillata ermeticamente sottovuoto. ✔️ASPETTI POSITIVI Ottima qualità. Anti warping. ❌ASPETTI NEGATIVI Nessuno! 📄CONSIDERAZIONI FINALI Utilizzo questo materiale da mesi, ne ho ordinati già diversi e mi sono sempre trovato benissimo. Qualità di stampa eccezionale, su centinaia di stampe non ho mai avuto fenomeni di warping. Non mi sarei mai aspettato una qualità simile, ho provato pochi brand in questo settore, ma questo è uno dei migliori anche a confronto con brand più costosi e blasonati.

Es el ABS que más uso, calidad precio estoy muy contento con él.