OHMOTOR Full Face Respirator Mask Activated Carbon Respirator Masks for Organic Vapor 4pcs Filter Cartridges

Just follow the instructions and you will be good, still wearing my glasses I placed it on my head and it fitted comfortably, one of the best I've worn as yet and at such a bargain price. Definitely worth the money.

I use this for airsofting and as a standby in case I ever need a full face respirator if the brown stuff hits the fan. My glasses fit well underneath, however the seal isn't perfect so if I needed it in a real situation I'd probably wrap something around the arms to finish the seal. It's not difficult to breath through even when running around for 3-4 hours in full kit and almost never steams up unless you're hot, stop, and your breathing calms before you cool off, you feel like you have to breath a little harder at first but quickly get used to it and the feeling disappears unless you're really pushing it with one filter on and the other hole sealed up with tape.My filters did not arrive with any cotton or covers.The visor can take a 340FPS plastic BB at point blank range without even a scuff, there's no damage to any of the mask after being hit in the face with BBs repeatedly during 2 games so far which speaks of the quality to price ratio. The straps to tighten it and latches to release it can be a bit fiddly to locate when you're in a rush, mask on, and have combat gloves on but not too hard most of the time.It can be difficult to sight a long-gun due to the visor and/or filters, but that's my problem and it outside it's intended use case (I'm just going to put the sight on a riser, and I have started to just remove the right filter and totally sealed it with a few layers of tape which makes it slightly easier, and it's still not hard to breath through).This £55~ mask I bought as a standby useful tool and specific costume item has actually replaced my £300~ goggle and mask setup for most of my matches now, and sits with the not-just-for-airsoft kit alongside my medical kit and a few other items that could come in useful in unexpected circumstances.I have not tested it with any actual chemical vapors, etc! However smoke from pyrotechnic grenades, other players farts, and hoards of sweaty manballs fighting around me cannot penetrate it noticably even with the minor seal breakage due to my glasses arms.

I got this to use as a dust filter for cutting MDF and working with loft insulation etc at home, and it appears to be fine for DIY use.It can be used with glasses but the arms do break the seal so it is not fully air-tight - although for normal use, the seal round the mouth and nose part of the mask is not affected. So again, probably ok for dust but maybe not so good for gas. It comes with a handy dandy little protective bag - but unfortunately it doesn't fit in the bag with the filters attached!The instructions are a bit of a joke - as bad as they were even before the days of google translate. For example:..... 'the mask default factory direct (that is, the filter element cartridge and do not use the airway) interface, the need to install the airway when the need to replace both sides of the interface and plug the other interface and ensure its airtight'.Contrary to one of the answers above, the instructions explicitly state that the 'Filter cartridge can NOT be cleaned'

I bought this to upgrade my woodworking PPE and it does the job. Even with a fairly heavy beard, you can achieve a pretty reasonable seal, but understandably, it is not a perfect seal. Vision is good, straps are well fitting and easily adjusted even with gloves on

Mask itself suits my needs perfectly. It is a good fit (small female) and comfortable to wear as it is very lightweight. I didn't risk using the filters that came with it, because even though they look similar to the genuine 3M ones, the writing on them wasn't in English so it was not possible to be sure that they were the correct ones to filter out the vapour from epoxy resin. They may be perfectly fine but I couldn't take the risk as I am horribly allergic to the fumes and it takes me weeks to recover if I'm exposed. I knew this before I ordered so it was not an issue for me. 3M filters fit perfectly.

A well made full face gas mask with the popular 6000 series twist filter system.Cheaper than many other full face masks, but don't let this fool you. I've used more expensive ones but they broke easily. This one looks much better. Very pleased overall. Only one thing I slightly dislike, I've got a long face so I can't talk using the mask or my chin gets slightly exposed . But it's OK, I just don't talk while using it

I am very happy with this mask. After spending ages searching for the right gas mask , I found this one. I bought it in case of a emergency. You never know what is going on in this world 🌍 especially since the Coronavirus started and everyone expecting a second lockdown. The world is changing folks and we have to change with it. I believe that everyone should have one ( Just in case ) I also purchased extra filters. Even though I hope I will not need to wear it, it’s still better to be safe than sorry. Very cool looking gas mask and very comfortable and the seller is very helpful. Must buy .

Bloody amazing product. People said it's not good for people who wear specs, well i have specs myself and if you wear normal glasses i.e. slim glasses they fit fine. I have rectangular glasses and they fit fine. I tried a pair of aviators on and put the mask on and they was a little bit tight but that should give you an idea. I have no issues with the mask at all great look great size great performance and no fogging. Definitely worth the money and would recommend to anyone. The only gripe I have is the fasteners for the bottom clasp is stiff but I have no doubts that after some use they will ease up... would Definitely buy more and recommend to anyone.