WochiTV Total Blackout Window Film 100% Light Blocking Non Adhesive No Residue Removable Opaque Static Cling Privacy Glass Tint for Home Bedroom Darkening Heat Control (23.6 in x 6.56 Ft)

Ordered the blue tint for our sliding glass doors. There is enough to cover both sides with an inch or two excess on all sides. Installation was tricky and is best done with 2 persons. The hardest part was cutting to dimensions as you need a large flat surface and the protective plastic film on the reflective side is thick and wants to re-roll. (Ruler markings on the protective plastic side would have been helpful). The reflective side goes on the glass. We had to spray the glass with water, place the film in position while pulling off the protective film all at the same time. (Be liberal with the water). Use a wet squeegee or rag for bubbles. (Don't sweat the tiny bubbles!) The film can be removed anytime with no damage to the glass. The film adheres well, even at the corners. The blue tint has a cooling effect indoors. The reflective side provides privacy, protection against indirect radiant energy, and reduces glare. We love this product and the effort to install it was worth it.

This works very well. From the outside all they see is a mirror. NOTE: at night if your lights are on, it losses its mirror effect and you can see in (never found one that didn't). EASY EASY to install. You do not need all that extra stuff to install. I installed it by myself. To clean the glass: I used a solution of 1/4 cup vinegar and 1 cup water in a spray bottle and paper towels or newspaper to wipe clean. Do NOT use ammonia based cleaners. For the "Application solution" I used a spray bottle with soapy water. (about 1 tsp dish soap to 1 cup water and shake well). Tip: Measure the glass in the window, measure and measure again before cutting the film. Add 1/4-1/2 inch overlap at bottom and side. Use a razor blade to cut off any excess after set in place. Tip: This is a vinyl film. No adhesive needed. It static sticks and you can easily unpeel and reapply to line it up just right. I suggest peeling the backing about 1/4 down from the top. With both hands line up starting a one top corner and top edge and work your way downward. The soapy water allows it to stick yet slide a little as needed. I worked the bubbles out with my hand. Definitely recommend.

I got the silver in 5 rolls. I noticed on 2 of the rolls, they had an indentation, almost like a small cut but still usable. Easy to install once you get the hang of it. You need: TO CLEAN WINDOWS: - Windex - Scotch-Brite Non-Scratch Scrub Sponges - Shower Squeegee - Scraper with Double Edged Blade (optional) TO INSTALL - FOSHIO 1PCS Green Squeegee Scraper Shower - Spray bottle - Johnson's baby shampoo (JBS) - cutter - Metallic Ruler (optional) Make sure you clean the window properly. To wet the window and the tint, mix water and JBS. Just a very small amount of JBS where you would have very minimal bubbling. Too much will make it slippery and will be harder to install. I think one of the reason why some complain that they can't remove the bubbles is because of using the wrong tool and technique. Get a squeegee with a handle (see my recommendation) because with it, you get more leverage to squeeze out the moisture when installing. You should also wet the film from outside when using the squeegee because it helps the tool slide better. The tint material is thick. You can put a lot of pressure on the squeegee to squeeze the moisture out which is good if this is DIY project. Once installed, you might see some very small bubbles (like a dot) here and there. After a few days, they disappear. From a far, the tint looks great. If you inspect very closely and at a certain angle, you would see some sort of a streak or pattern on the tint (see pix on what you can see from the other side, some distortion). So it is not like a mirror finish. I would rate the quality 3 out 5. I guess at this price point, I can't complain. I gave it a 4 rating overall. 20200711 Video Added: Using squeegee to remove water between tint and glass. One I’m using I highly recommend.

The product works without any adhesive, which is fantastic, cleaning the surface well will help and most importantly: since it comes rolled up, you first need to do some "unrolling" to flatten then sheen, otherwise the sheet will bed away from the glass and end up falling due to gravity. In my case 99% of the sheet adhered to the glass perfectly, and for the flaring edges I aplied a small tape to secure them

So it has definitely kept the morning sun out of 1 room, but it looks pretty lousy with bubbles - I think these are unavoidable. Its easy to fit once you cut it. Instructions are fairly idiot proof .

Got this to stop a very nosey neighbour from looking into my bedroom whilst I take a nap during the day. Very effective and look great from the outside. Instructions are scarce and it takes patience. Some tips. 1. Don’t worry too much about the size to cut. Just make sure the film is larger that the window you are going to fit it onto. It’s very easy to trim any excess film after it’s fitted to the window. 2. Use a table to measure and cut. Trying to do this on a floor will attract a lot of dust particles etc. 3. Make sure the window is very clean before applying the film. 4. Maybe use distilled water to moisten the window rather than tap water if you live in a limescale area. Also don’t use a sponge to apply the water, use a spray bottle for even water distribution. 5. Use a squeegee to squeeze out the water after fitting but wrap the squeegees rubber blade in a soft cloth to stop the squeegee rubber blade from scratching the surface of the film. 6. Yes, if you make a mistake it can be removed and reapplied. 7. After about a week, the film becomes more clear and less cloudy on the windows giving a nice look from inside also. I’m now looking for other places to use this film. Just love the way it looks on my windows.

A very good option if there's a bad need of privacy and curtains aren't the proper solution. This film is a very good choice for the case if there's a window that doesn't have to show inside but needs light. The roll comes quite big, the film itself looks done well. Even if it's advised to use it for Windows and stuff, I've tried with a narrow piece on one of the wardrobe doors and now instead of useless glass in the door, a well placed mirror looks much better. There are two issues that makes it 4 stars worth only - 1. It will not be able to apply on textured glass. I've got this type of glass on the front door and tried to install but no success - lots and lots of bubbles plus removing by itself in some places. 2. Fantastic privacy and good sun protection but when the night comes, the lights turn on and the privacy is over - the window become transparent again. Not too difficult to install - clean the window, spray a lot of water and basically that's it. Good thing, but sometimes not too helpful.

Found this easy to apply but keeping it free from airborne particles before getting it on difficult no matter how careful one is...