BOSCH RA1171 25-1/2 in. x 15-7/8 in. Benchtop Laminated MDF Top Cabinet Style Router Table with 2 Dust Collection Ports

BOSCH RA1181 Benchtop Router Table 27 in. x 18 in. Aluminum Top I put it together. Haven't yet put it to use. I'll only speak to what I can tell from the assembly. Great instructions! Bosch has gone to great lengths to take all guess work out of the assembly process, something other manufacturers should take a lesson from. The paper booklet is much better than online manuals, although I used both at different times. For those of use who think manuals are an unnecessary imposition on our God-like intelligence; I suggest you read the manual at least a little in advance of the parts you're assembling. It might save you some assembly-disassembly-reassembly. Don't ask me how I know. You know how I know. Ever wondered which bolt is the #10-16 x 1/2" and which is the #10-24 x 1/2"? The paper booklet has a true-to-size print of each and every bolt, washer, nut, etc. that solves the mysteries of identifying an incredibly large number of parts that come with the router table. How many parts is a large number? There are 161 parts, a few of which are for other models of Bosch router tables. A key identifies each part with a number that matches the true-to-size part's representation in the booklet. BTW: I didn't notice any Chinesium fasteners whose Philips head screws round out with the slightest bit of aggressive twisting of the old driver bit. All the fasteners are of a quality you might find in something like automotive manufacturing. All the main component parts are solid and well-made. Plastic is not all made the same. Time will tell how the plastic components hold up, but I expect they'll do just fine. I was very surprised at how sturdy the aluminum fence was. The same for the aluminum router plate and table top. I did not expect them to be so heavy. When I was removing the table top from the carton I wondered, due to its weight, if it was steel rather than aluminum. Leveling the router plate: I've seen reviews that made comments about the difficulty of leveling the router plate and aligning it to the same plane as the table top. I found no problem with this at all and verified the results with a TSO MTR-X triangle. I didn't go so far as to get out a set of feeler gauges to look for thousandths of an inch differences, but I don't expect to be routing components for use on Space-X. It's woodworking, not rocket science! Price: I got a terrific Black Friday price of $172.81, or so I thought. It's still (12/20/24) listed at about the same price on Amazon. I am not a connoisseur of router tables. I did the usual due diligence one might expect a penny pincher to do when making a purchase that offers the best of everything at the lowest price available and I think it went a lot better than expected. I wasn't looking for a table that cost $400 or more. I wasn't looking for the largest table or one that attaches to a Festool MFT. I wanted a table I could use in the basement or out on the driveway and pick up and carry to a job site without too much muscle strain that was suited for making moldings, dados and so forth. I was first looking for a table with a two part fence so it could be used for jointing. I admit to being disappointed that the best table I found did not have that feature. It took a while to find a Youtube video that spoke to this problem. But Bosch solved it by including two 1/16" "Jointing Shims" that slide behind the out feed fence to allow edge jointing in increments of 1/16" to 1/8". It's not an infinity of adjustments but then no fiddling is required to set up the table for jointing. Just slide a shim behind the fence and you're ready to go. So, that may actually be an advantage over two separately moveable fences that require careful alignment to get the right cut on an edge joint. I rarely give five stars but I think they are well deserved in the case of the Bosch RA1181 and the great Amazon price. For $175, how can you go wrong?

Disclaimer: I'm a wannabe woodworker headed for retirement and a mechanic of 40 years experience. Assembly was a breeze really. I got it mounted and running in 90 minutes. Identifying and sorting all your parts first will help. Having a ratchet with an allen-head socket will speed things along too. Although I would have preferred a full sized router table with a cabinet, my limited space made it impossible. (If I told you how small my shop was, you probably wouldn't believe it.) Naturally, in the process of buying something I really didn't want to buy, I did lots of research. I buy with value in mind employing a computation of price, quality, quantity, reputation and life cycle. I have NO allegiance to any brands or where any product is made. I had a chance to see and touch some of the competing models of bench top tables including Bosch's other model 1171 and rejected them all for one reason or another. The numbers (including a great sale price from Amazon) landed me on the RA1181 with trepidation after reading many reviews and not being able to get my eyes and hands on one. As a mechanic/technician, I'm fairly picky about machine tolerances so, I was a bit put-off by some of the reviews I've seen complaining about warped tops. I fully expected to go into this with having to do my own machine work to the top in mind. As soon as I opened the package I went over the top with a 12 inch machinist's bar and a feeler gauge. I did it again after assembly. I found no high points and the lows did not exceed 0.004. I don't know about everyone else but, that's damned near perfect and less of a variant than I know I'll experience from the materials (wood) I'm working with. Wood, depending on how dense the species is, will expand and contract over time, humidity and temperature at least as much if not more than 0.004. If you want better than that, I would recommend prying out a few grand for a cast iron shaper. Testing by bridging the over the insert found it dead-on. That's good enough for me. I found the fence to be fine. The hardware is robust enough that they all stay put during operation and should last. I saw some complaints about the fence material. The metal extrusion is also dead on and the faces are what appears to be melamine. Good enough when you consider that they are sacrificial. Replacing them shouldn't cost much and they shouldn't really be replaced with anything other than what they are. I really like the dust extraction feature. Some bigger chips do fall underneath but, the flyable dust seems to be getting sucked up pretty well. I'll put the efficiency, conservatively, around 70%...'your mileage may vary'. The included shims to set up for edge jointing is a nice touch and I've used it twice already. Works great. Speaking of 'nice touch', there is an outlet to support your shop vac or whatever you're using as a dust extraction system, a real time saver. No Miter Fence? The track on the table is not for a Miter Fence, it's for the feather boards. Everything I've studied says that you shouldn't use a miter fence on a router table or any other tool that has a parallel, rip, oriented fence. I square up a piece of scrap and tack a guide on the end so it follows the edge of the table top. Works fine, quick and easy to do and provides a nice back-up to prevent tear out. Downers: Of all the dimensions I was able to find prior to purchase, there was no mention of the base. There is a dimensional diagram on the box but, still no mention of the base bottom. I incorrectly assumed the dimension would be the same as the top. Be warned that the base, at the mounting holes, is wider than the table top. It didn't fit the workbench I had to make in advance of receiving the tool. I wish the carriage bolts in the feather boards were a little beefier but, that's only a little annoying in initial set up of a project. Yes, the base of the table is plastic but, it's made with enough ribbing support that it's very strong. The unit doesn't rack at all. I just wish the same theme was followed with the switch fascia. It's sort of adequately supported on one side only and feels cheesy as it deflects when operating the switch. But, it does work and we'll see if it lasts. I'll just have to discipline myself to use my fingers rather than my knuckles like I do all the rest of my tools. Summary: Other than those couple of nit-picks, I'm pleasantly surprised by the convenience and functionality of this tool and would recommended it to the small-shop woodworker without much reservation. I've done a couple of projects with it, got no surprises and it has already paid for itself in saved time and aggravation. The days of having to whack together all sorts of elaborate jigs to compensate for not having a router table are over, thank goodness.

The Bosch RA1171 Benchtop Router Table is a good table for the money. The router mounting plate is aluminum, very sturdy, and fully adjustable to ensure it sits flush with the tabletop as explained in the included assembly instructions. The router mounting plate is compatible with a variety of routers - see photos for a list of routers (accurate as of today, 12/21/22). Once the table is fully assembled, it is very sturdy and easy to secure to a work surface, bench, stand, etc. There is one modification that, while not critical, I do recommend. I found that when I tightened an accessory down to the outer edges (far left and far right) of the Aluminum Miter Channel, the channel would flex and pull away from the tabletop. This happens because there are only three mounting screws used to hold the miter channel in place, and they are located more towards the center of the channel, leaving the outer several inches on both sides unsecured - see photos. The fix is easy. I drilled a 3/16" hole through the aluminum miter channel and completely through the tabletop, one inch in from the left and right ends of the miter channel after installing it to the tabletop. Then, I countersunk both holes to accept new #10-32x1" flathead machine screws making sure the tops of the screws would sit below the surface of the miter channel, just as the three screws provided by Bosch do - see photos - the two silver-colored screws on the outer ends are the new/added screws. The three black screws in the center are the ones provided by Bosch. The new #10-32x1" Screws are held in place by a Flat Washer and a Keps Nut on each screw from the underside of the tabletop. Tighten them securely. See photos for a closeup of the screws, washers, keps nuts, and one of the new screws installed in place. After completing this modification, the outer ends of the miter channel are now firmly attached to the tabletop and they will not flex when tightening accessories located in these areas.

I purchased this router table recently for my Bosch MR23 router. I have a small shop so a huge router table is out of the question. I have always liked Bosch products so I gave this a try. After reading a bunch of material on the different Bosch router tables I was directed to go for the aluminum top model instead of the other models for durability and accuracy. TAKE HOUR TIME putting this together and make sure you use the exact recommended screws in the exact positions they go in. The direction photos can be hard to make out at times but the directions are thorough enough to allow you to get the job done. It took a few hours to put together properly and square/level everything up. You will have to use a zip tie around the trigger button of the router because you will now turn it on from the included switch which is a nice included avcessory. My first job was rooting a bevel edge on a door threshold piece of corian I was needing and it handled it flawlessly! The table exceeded my expectations. It comes with 3 different inserts to fit different size it’s, a corner guide pin starter, feather boards, etc. For this price I simply can’t imagine anything being better than this. I checked the squareness with my gauges and the table/fence is dead square out of the box. If you are looking for a small benchtop router,I think this is the best in its class by far!

Okay, I know my needs are quite specific, but I've not seen my solution anywhere and it's working great, so I wanted to share it: I bought this Bosch router table because of the size of its top and the fact that the top is METAL (I'm distrusting of the durability of those MDF tops). The table is terrific and an incredible bang for your buck! My specific needs, though, were for a capable and PORTABLE router table. I use it at home but also will need it for building film sets at my company's first video studio (we're currently building the studio itself). "Benchtop" implies that you could set this on a bench and use it... bad idea. You'd be routing at face level. The stand makes the tabletop too tall for a bench or a miter saw stand and too low for the ground. "Tabletop" would be more accurate, but even a kitchen table height makes it uncomfortably tall. Regardless, I had portability to consider and a budget I wanted to stay within. My entire routing solution was as follows: I purchased the Dewalt 618 router package with the fixed and plunge bases. I mounted the fixed base to this Bosch table, leaving the plunge base available for buying a second DW618 motor only for handheld routing. Then, after a lot of research, I bought the DW7440RS Rolling Table Saw Stand. It's very low and puts the Bosch router table at the PERFECT operating height for me (I'm 5'9"), with the added bonus that it folds up and rolls away. I may have the world's most portable routing setup. Haha! Anyway, it took me a lot of research to figure all of that out, but I feel those three items were a great compromise for my budget requirements. On the DW7440RS stand the Bosch RA1181 is sturdy but portable, and I've really been enjoying it!

I just finished a set of raised panel cabinet doors which is about the most challenging thing I use a router table for. The doors ended up nice with good fit, the minor flaws are most likely do to the operator not the tools. I am by no means a pro but here are few points I noticed while using the table: 1. Assembly was not particularly difficult but expect to take some time to do it right. The instructions were adequate. 2. Leveling the mounting plate got a little frustrating, but I tend to get hung up making things perfect when they don't need to be. In the end I got it level with the table (more on this later). 3. Setting up the table for use was easy, the feather boards were solid, worked well, and stayed in place as did the fence itself. I have to admit, the guard that attaches to the fence didn't last long with me, but removing it is easier than installing it. I will most likely regret this decision the first time I get my fingers tangled up in a spinning bit. 4. The table surface left some mar on the wood I was using, but nothing that wasn't easy to sand out. I imagine that this will go away as the table surface gets used. If you really wanted to I'm sure you could polish the table surface before first use. 5. I have a Bosch router so the table top depth adjustment feature worked with my router. However, the combination of having to clean out the dust from the hole every time and keeping track of the allen wrench made it a rarely used gimmick. I ended up just making all of my adjustments from under the table. This is how I adjusted on my old table so it was not a big deal for me. 6. Chip collection was decent using a 1HP shop-vac, but I would continually blow the breaker in the table switch with both the vac and the router plugged in to it. Based on the current rating of the switch (15A) I shouldn't have had both things plugged in to it; so chalk that up to operator error. Now for my main complaint. As was mentioned in a few other reviews my table top had some significant crown (a little over 1/32" or 0.03125"). 95% of the time this probably won't be an issue but I emailed Bosch anyway. Per the response I received, the manufacturing tolerances are a max crown of 0.5mm (0.02"), so it would seem my table is out of spec. It's the weekend so I will have to wait for Bosch's response as to what I should do, but even with the out of spec crown the table performed well. Overall, I would recommend this table to a friend who was in the market for a sub-$200 router table. *EDIT* After a brief and friendly email exchange with Bosch tech support they shipped out a new table top which showed up just a few days later. This one was perfect and they did not ask for the old one back making it a rather easy process. I upgraded my review to 5 stars due to the excellent support I received.

Replaced an old Craftsman router table and what a great upgrade. Really a quality product and I thought it was priced very reasonable.

Just got this assembled and it looks like it will work fine for what I need, but there are a few design issues that appear to be caused by using cheaper hardware and packaging. Examples: - The screws that hold the cabinet together are nice and go in well, but the supplied wrench doesn't fit them very well and slips out constantly while trying to tighten them. - The screws that attach the door to the cabinet are smaller than my number 1 Philips. You need a jewelers screwdriver to fit the head.. Have you ever tried putting in a wood screw with a tiny screwdriver? Even with the pre-drilled holes, it's VERY difficult. - Do yourself a favor and buy (6) #5 or #6 5/8" #2 Philips wood screws and don't use the ones supplied. - The fence is nice, but they need plastic spacers to hold the feather boards out far enough to not hit the wooden inserts on the fence. - The feather boards are poorly packaged in a box with heavy parts and can easily be damaged. - To Bosch's credit, I called and had replacement feather boards within a couple days. But, a little foam blocking around the loose parts would have saved that headache. Overall, now that I have it assembled, it's nice and sturdy, has a couple options for dust collection, and it is a nice upgrade from my old router table after I paired it with the Bosch router. I mounted the Bosch 1617EVSPK in mine. Fit perfectly, and the screws to mount the router to the plate were included. Pros: - Nice and sturdy once you get it assembled. - The leveling feature for the router plate works well. (Adjust the screws under the plate, then tighten the plate down) - The fence is nice and sturdy extruded aluminum. - The hole in the plate for router bits can accommodate large diameter bits - Nice thick router mounting plate with lots of mounting options for many routers. - Easy to mount the cabinet or clamp down, but for light work it's heavy enough and just putting an anti-slip mat under it should keep it in place. - You can store parts such as router bits inside the cabinet, however, that will come at the cost of getting them full of dust if you don't build a covered tray for them. - Enclosed cabinet makes the router quieter. Cons: - Poorly packaged. Bosch needs to understand that these heave boxes will be banged up in shipping and there needs to be foam inside to prevent damage. Saving a couple bucks on packaging costs more in damaged parts. - Assembly is easy, but fastener choices need to be looked at. The supplied wrench barely worked for the cabinet screws and needing a tiny jewelers screwdriver for the hinge screws is terrible. - Plastic spacers for the feather boards would not have been needed if Bosch had used thinner panels on the fence or a slightly different extrusion profile. - No cable management for the power cord inside the cabinet. - A knob would have been better than a hole for opening the door. If you open with right hand, be careful not to break your finger when it gets over half way open. The momentum of the door grabs your finger.