Q Power 10" Single Subwoofer Box, Vented Speaker Enclosure

Great subwoofer box for the value and quality build. Added an American Bass 10” sub XO-1044 and it fits perfectly and sounds great with the sub. The specs for the subwoofer and subwoofer box are a perfect match.

Box fit perfect. Sound hits hard made with good quality material

All in all, this a great little box! One big plus is that the opening was NOT 9" as stated, which would be too small for most 10" subs. It is in fact roughly 9-1/4"... much more appropriate! I say "roughly" because top to bottom, the opening in my box was a hair over 9-1/4". Side to side, it was a hair under. So my sub almost fit perfectly, but not quite. I'll need to trim / sand down the left and right sides of the opening a little bit, to get them up to the full 9-1/4". It seems the manufacturer may need a new circle template... As others mentioned, it is indeed 3/4" MDF on all sides, and 1" for the baffle. Seams are all sealed with wood glue. The port interior is painted black for better appearance. I wish the carpet was black, and a bit thicker, but aside from that, it seems durable enough and was well glued down. The carpet around the port opening had a few small overhangs, but nothing a fresh utility knife blade couldn't take care of in seconds. One other wishlist improvement would be if all the edges (except the speaker opening) had been gone over with a roundover bit, just for a bit better appearance. Terminal cup is nicer than the usual, black / red plastic ones. Aside from the minor gripes mentioned above, it really is a nice little box for the price. And bonus for me, it is almost exactly the right airspace WINisd suggested for my specific sub!

All the important stuff we really want to know: -The baffle is 0.9" thick, not quite 1". -Balance of construction is 0.750". -The port displacement is 0.3 cu ft, making the actual internal airspace 0.723 cu ft. -Speaker cutout diameter is 9.125". The only negative would be the fact that the slot port is "stepped". The first part moving towards the back of the enclosure is 1.875" wide, but the "L" or "turn" is 3" off the back panel which makes calculations very difficult when trying to match to a compatible driver. I've determined the slot port is approximately the same as a 5" diameter port that is 16-18" long, acoustically.

I picked up a dirt cheap Kicker Comp 10" sub on a thrift store visit and this box was approximately a good fit considering the TS parameters. It's not exact, but it was also cheap and I didn't need to build a box for so I won't complain. Currently filling in the low end for a pair of cheap bookshelf speakers. The TV is old and gets attached to whichever older gaming console I'm interested in at any given moment. Powered by a 100W chip amp and while it won't shake the dust off the walls, it works well enough that I can't quite justify throwing together a more comprehensive setup.

Kicker comp c 10 inch sub fits perfectly. Way better than original slim box it came with. Had fuller sound and also doesn’t fall over.

Arrived in great shape, quality sound . Fyi, I never just throw a speaker in one of these prefabs but at 50.00 and up a sheet plus my time? It's a great value, I really like this box

Very heavy duty and well-made product. I can see the quality workmanship that went into building these Speaker Boxes. Very impressed and I will definitely purchase again when needed.

Box feels solid, looks good and measurements check out. 1" baffle and 3/4" construction as described. Box fits my sub but I haven't installed into the car yet. For the price on a prefab box, I can't complain. People who complain about the cut in the carpet, that's where the seams meet. I wish it was on the bottom not the side. But once in my trunk, who cares...?!! Will update I'd there is any issues once installed. But I don't foresee any.

got the box for less than I could buy the materials for let alone the time it would take me to build one.Excellent design with built in vent and my 10 inch subwoofer fit perfectly.I read one review the the speaker conector on the back was flimsy they must have fixed this problem the one on mine is nice push and release and fastened in solid.I highly recommend this product

Quality product and quick shipping

Comme d’autres l’ont mentionné, la finition est très ordinaire, mais pour le prix, c’est correct. Cela m’aurait coûté le même prix l’avoir fabriqué moi-même. J’ai imprimé en 3D une finition pour l’évent.