Boncart High Strength AB Epoxy Putty, 200g Steel Reinforced Repair Filler

This works well. Instructions are easy to follow. I used this product for two different types of repair. First was a chip out of my porcelain kitchen sink. It did the job. Second was to reattach a plastic piece that had broken off a plastic bin in my refrigerator. It worked well with this application as well. If you are just patient with this product it will do all you want it to do. It took about 2 hours to begin to set and was completely set after 24 hrs. It set hard as a rock . I was very pleased with this easy and versatile product.

Wear the included blue gloves. This epoxy is not toxic but it's sticky and gooey and you'll have a tough time getting it off your hands! Part A is the most messy, but cutting off an equal part of Part B you can squish them together pretty well with the gloves (although it will try to stick to the gloves too.) I've had this life-sized head on a neck and base that needed improvement, sitting on a shelf with about 10 others in various stages of completion, so it was time to do something about it and find out how this Boncart epoxy works. I decided to change her top lip, move it up, and make her a happy grin instead of the more neutral expression she had. Cutting it out and digging enough space to raise the top lip, it was time to mix the epoxy putty to hold everything in place. These heads are mostly paper and glue on solid wood armatures, so the epoxy has something to grab on to because it's solid material that takes the most time to cut through. Epoxy has to be completely mixed and will harden with Approximately Equal portions. It doesn't have to be exact, but BETTER IF IT IS. The mixing is more important. After putting the 2 chunks of sticky stuff together you can work them into a ball, then flatten the ball, roll it up and turn it into another ball. It takes about 30 minutes to start to harden, so you have the time to mix it like that until it HAS to be uniform. 5 minutes isn't too long to mix because if it fails it's BECAUSE you didn't mix it enough. Some of it on the inside cavity below the nose and some on the upper lip and pushed in and up, remembering the top lip will come out just a little more forward. Some of the epoxy becomes the now visible teeth under the upper lip. I don't worry about details, just the big features. Later on when it's hardened it can be carved, rasped and ground to shape. The epoxy is bright white and it can be spread quite thin with the nice flat tool with the triangular sharp edge. The tool is a good one, flexible and light that makes moving the stuff around easy and making sharp edges in the epoxy, separating it into small parcels to be spread out. >>>It would be nice if the 2 parts each came in a SEPARATE color so mixing it would clearly show any non-mixed parts.<<< There's even a few pieces of rough sand paper discs for smoothing the hardened surfaces, but I've already got that covered. This kit is for doing it without any other tools, just what comes in the box. When you open the parts A & B there are extra plastic bags to wrap them back up. It might not dry out for a long time and still be good, but you don't want dust and other things to get into the mix. Remember, IT'S REALLY STICKY & GOOEY! (The Next Day) Epoxied areas are hard and smoother than they were. The epoxy sort of glazes over as it sets-up. This might not be good if you wanted some surface roughness or texture, but in this case it's mostly structural and will be covered by layers of thin paper/glue as required. Each of these heads has an expression and those that are successfully completed and good enough get sealed with acrylic or varnish and used to make a mold.

Purchased this product to try plugging into an external door jamb that over the years the externally facing bottom 6 inches or so has partially rotted away due to moisture absorption from the elements. After getting a few outrageous estimates to replace the door frame, I then removed the rotted wood and tried applying copious amounts of caulk to the gaps - a repair which indeed worked but lasted for about a year until it began crumbling off. I figured before I go and buy some lumber to try to cut a custom sized piece of wood - that I would try this moldable epoxy product product instead. So far I am glad I did. The epoxy comes as two slabs of clay-like material. To use it, you take equal amounts of each material and with your hands, knead them together until they are well blended before pressing the material into whatever hole/section you wish to repair. The kit supplies you with a pair of loose fitting gloves to aid in this process as the materials are a bit sticky. I found that the materials were very stiff and firm and it took a good amount of kneading and requires some forearm strength to mix them well. Once mixed I found that the clay was easy to apply to the sections of door jamb that I had previously cleaned out. The epoxy dried/hardened to the touch within an hour and was fully cured the next day. I did find it a challenge to shape/mold the clay since it is very stiff, however since it fully cured overnight I was able to sand it to fit the contour of the frame better. It accepts paint very well. It's wait and see for now as we head into winter and the cold/wet elements. So far so good.

Amazing! I’m a thrifter and always turned down adorable ceramic pots due to a crack. This has been a game changer. Bought a very large strawberry pot that had a crack 1/2 way from the top to the bottom. No leaks (I water the plants in this pot everyday). I didn’t paint the crack cause I like the way it looked on the clay pot.

Bottom line: This is a great product and priced fairly (around $10 when I bought it). I trust you'll be pleased as well. More detailed version: I'm extremely pleased with this product, and I am going to start making sure I always have some on hand for repairs. I've used it for both outdoor repairs and indoor repairs, and ranging across material types, and each time I've been very pleased. It functions as described. It gives a very durable bond, and is relatively easy to use. Depending on the nature of your repair, you will need patience and some fine-point tools (e.g., I did a very detailed repair of a ceramic item that had shattered, requiring a stepwise repair and recreating surfaces that had been ruined), and I do recommend wearing gloves when working with this (the vendor includes a pair, but you might want to just buy a box of disposable gloves). One other tricky part is the compound can start adhering to the gloves a bit, which can make manipulation of the compound a bit more difficult as you continue to work with it. But it's hard to complain about that, because it's hard to envision what could be done to offset that. Again, this is a great product, and I'm sure I'll be buying it again.

I've bought this product several times and I love to use it when needed. Make sure you mix evenly for best results

Really messy to use. Use lots of plastic gloves and clean up QUICKLY after application. Didn't hold up well when used to fix a cracked plastic seat after 24 hours cure even after grinding out the crack before application.

Drejons Epoxy Putty worked great! It was easy to mix, applied smoothly, and hardened strong. Perfect for quick repairs and projects around the house. Great quality for the price, and I would definitely buy it again!