MICROJIG GRR-RIPPER GR-100 3D Table Saw Pushblock, Yellow

Such a great woodworker's tool! It's solid and grips well. It feels safe and comfortable using this instead of the default pushbar that came with my table saw.

The first thing I noticed when I opened the box was the quality and craftsmanship of this push block. It was easy to assemble and the versatility and safety of this push block was very impressive! The handle gives it a good grip and functions as it should. The rubber grippers on the bottom holds the material you’re cutting tight and keeps your hand well away from the blade while cutting. For what this is at this price point, you couldn’t make one at this quality. I own the Matchfit clamps which are also great quality and work well. I’ll definitely be getting another one of these push blocks and I highly recommend it!

Worked great. Replaced the missing blade guard and wood pusher. Felt safe.

They call it a "Micro" jig for a reason. This is suitable for cutting small pieces and doing a lot of them. Since you have to completely set the jig up for every cut you make it is a lot of setup when you are making only one cut. Also you can only raise the blade a little bit so it sneaks in under the "roof" of the push block. I like my blade raised up higher so when it enters the wood it is pulling the stock down onto the table saw not right at you. I'm keeping it as well as the GRR-RIP BLOCK because I will find that very useful when using the router table; it's great for that. For the table saw I have been using the Vermont American 26778 Push Shoe Assembly which is currently unavailable. You can Google that to get the idea by seeing it here on the Amazon page. Everyone has their own way of doing things, and I have been woodworking professionally. I use leather gloves like they sell at Home Depot. I realize that the table saw blade only moves one way. So anything you do on the side of the blade that is closer to you is not going to result in a finger loss. So I take my larger boards and support them, and feed them into the blade by using my hand as a guide to push them into the fence and allow the board to slip by. That is why the leather glove is so important; it slides real nice. You can't do that with your bare fingers. I keep the push stock Vermont American handy just to the right side of the fence, and when I am finishing my cut, I pick it up, and hook the rear tab on the edge of the wood. My pushing motion is at a 45 degree angle toward the fence, not the blade. So if there is a slip my hand is moving over the fence not into the blade. Since the Vermont American is so tall my hand is always well above the height of the blade. Once I pass through the blade, and the piece is not south of the blade I give the V American a little twist and it pushes the cut piece just a little away from the blade to the left side. So I am not placing anything, or grabbing anything to the north side of the blade. That is the danger zone. Everything is done making contact between the wood and the fence. Okay so now back to the Gripper. If you are making repeatable cuts and you need let’s say 1/4" cuts the gripper is ideal for that. Myself personally I don't like working under such tight tolerances when it comes to gripping the stock. It brings a lot of dangerous possibilities into the mix. The Gripper virtually eliminates all of those risks. It's a pain to have to set it up for each cut, but if you are making a lot of the same pieces it is worth it. What I do when making sliver cuts for stock that is real thin, I run the large part of the board between the fence and the blade, and leave the sliver to the outside of the blade. You may be thinking why do that? You won't be getting consistent cuts that way. Normally that is correct, but I have an Incra Table Saw fence I bought here at Amazon but I don't see them carrying it anymore. It cuts accurately to within a thousandth of an inch, repeatedly, easily. Too much to explain. But anyhow I also use the Forrest Woodworker II blade which is exactly one eighth of an inch wide. So I can dial in the fence to be whichever size I need, plus one eighth to account for the blade. Perfect repeatable cuts without having to worry about trapping a quarter inch wide piece of wood between the blade and the fence and having to squeeze your push block along that narrow trough. You could do this manually with any saw by simply making up a sample guide piece that is the width you need, plus whatever the thickness of your blade is. Then you manually adjust the fence using the guide piece and lock it down. You can get some very accurate cuts this way. The alternative is set your fence once and forget it using the GRR-Ripper 3D but once again you are making a very inflexible cut. No matter how you look at it if you blade catches the edge of the gripper something ugly is going to happen. This is all about safety and the Gripper enhances that for small pieces. It's not cheap, but neither is losing a finger. I will be getting a lot more use out of this on the router, and the band saw, or as I mentioned for cutting smaller repetitive pieces on the table saw.

Let's talk about the MICROJIG GRR-RIPPER GR-100 3D Table Saw Pushblock. This thing is like the superhero of table saw accessories. If table saws had capes, the GRR-RIPPER would be the Batman of the workshop. First, the grip on this thing is tighter than your grandma's hug on Thanksgiving. You put your workpiece through, and it holds onto it like it's the last piece of pizza in the box. No slipping, no sliding – just a solid, confident grip. It's like having an extra pair of hands, minus the annoying backseat woodworking advice. The 3D design is pure genius. It's not just a push block; it's a game-changer. You can pull, angle, and tilt your wood precisely. It's like giving your table saw a Ph.D. in woodworking. You can kiss those kickbacks goodbye – well, almost. The adjustability is on point. You can set it up for different cuts and angles without feeling like you need an engineering degree. It's like they thought, "Let's make it easy for the regular Joe in the workshop." Plus, it's got these green grippy things – not sure what they're called officially, but they're like little green traction ninjas ensuring your wood stays in line. Safety-wise, it's like having a bodyguard for your fingers. You keep your digits far away from that hungry saw blade, and it's got this non-slip material that's like, "No, Mr. Wood, you're not going anywhere without my permission." Sure, it might seem a bit pricey for a push block, but let me tell you, it's worth every penny. The tool makes you question how you ever did without it. You're missing out if you're serious about woodworking and don't have one of these bad boys. The MICROJIG GRR-RIPPER GR-100 is the table saw's best friend and your fingers' savior.

These are awesome. I'm an old man and wish they'd been around years ago. These are worth every penny. Although I still have all my fingers and both thumbs, these are a must for anyone in the modern wood shop. Versatility and safety in a single package.

I was looking for a safer push block with more features and adjustments for different projects on my table saw and this looked like it fit those needs perfectly. I've used it quite a few times now and I really like it. The inside adjustment works well to move it away from where the saw blade will be and still provide great grip and I also like the adjustment bracket on the edge that lowers to the table to keep the push block from tilting. It is made from good material, not too heavy and not too light and flimsy. I'll likely buy another one sometime down the road for cutting longer boards because it is versatile and works well.

These things are absolute life (and limb) savers especially for beginner saw users. I used to be scared of cuts on my table saw and now feel confident to use it regularly with these jigs assisting me. This is my second one to help me rip larger pieces of wood. A little expensive, but for the peace of mind they provide they are 100% worth it.

Top Produkt ist schon bisschen teuer!!! Aber sollte in keiner Werkstatt fehlen wo nee Säge ist . Und der Preis na ja , aber es Schütz meine Finger 😜. Würde es jederzeit wieder kaufen ,

Great

I hated having to buy this because of the price (my wife gifted it to me eventually) but now that I have it, I am very pleased with the quality and design. It does what it says it will do and does it extremely well. So, materials wise and design wise, it's great. It's marred only by its extortionate price tag.

All good, and the manual is well-written as well.

Muß man einfach für die Tischkreissäge haben.