Thermalright LGA1700-BCF Black V2 CPU Anti-Bend Fixer, Intel 12/13/14 Gen Anti-Bend Fixing Fixture, Intel CPU Corrective Fixing Bracket, LGA17XX Corrective CPU Bender, LGA1700 Full Fit Fixer

This is a simple product that has the potential to drop your socket LGA 1700 CPU's temperature down by 5-10C pending if you have a motherboard with a significant bend on your Intel processor. In general, when paired with a high quality thermal grease, this can have a big effect on temps. Due to its very low cost and how easy it is to install, it makes no sense not to use this.

CPU temperature is 20 degrees LOWER than expected while running BattleField 6 on an i7 14700F. Excellent. Easy to install. Durable, strong material. Compatible with Intel 14th Gen i7. Exceeding Performance expectations. Note: I applied a thick line of thermal paste (Corsair XTM70) from the top center to bottom center of cpu, then lowered heat sink. Even displacement.

No issues at all. Everything needed to install provided.

I've been in Hi-tech mechanical & thermal design for decades with many a new CPU board in my design experiences. I've disliked the load the LGA socket frame design would put on a PCB since day 1 of that socket's intro and would try and augment our rather dense LGA based board designs around the CPU when I could. This inexpensive gem is an eye opener and I purchased one as soon as I saw it for a new build with a new MB with a new CPU after my venerable 5th Gen MB recently gave up it's ghost. It takes maybe 5-7 minutes to remove the LGA frame and install this along with your CPU. The bow in the PCB across the processor is nearly non-existent. I've also never seen a CPU run this cool using a forced air heat sink let alone this newer one at essentially double the TDP of its predecessor. Too many things changed on this new build to accurately determine what the full temperature drop contribution was. This new board included the use of a 6x6mm heat piped, single fin-stack heat sink and 15W/m-K thermal paste. My Core temp at idle is running a couple of degrees C above ambient and my local PCB temp is about 6C over that indicating a better transfer off the bottom of the chip & socket into the PCB. My guess is that when installed right with a really thin layer of a good thermal paste and clean/dry surfaces, its good for double digit improvement as others reviews have stated. My immediate reactions with this at first power up was literally, this temperature can't be right, but apparently it is. On an older 12th-13th-14th gen board with the bow at the CPU already "baked" in, your results probably won't be as good. Likewise, if you don't get rid of the little thread particles the typical cleaning pads leave behind prior to thermal paste application, you also won't see as much improvement as you could. For as little as this costs and for what it does, I highly recommend this as a standard feature for any build where Thermalright has a size match for your socket; currently AM4 & AM5, LGA 1700 and probably the 15th Gen 1851 socket (if not now, soon). 5 stars only because that's as high as you're allowed to go.

Perfect. Fits like a glove, easy to install

If you are looking for a little extra support for your M/B CPU socket, this is allot more support. The Thermalright LGA1700-BCF Black V2 CPU Anti-Bend Fixer Bracket fits perfectly and looks great. For $7 plus tax with Prime, you won't be disappointed. Also, won't get in the way of your CPU cooler and any type of cooler will fit without problems.

Works great on my 12600K that has LM and quite a harsh high voltage overclock. I did not do a ton of measuring and testing, but during specific memory testing and Cinebench runs, temps were on average around 8-10 degrees cooler. This does not mean YOUR cpu will see same differences. One thing others do not do, I removed it and went back to Intel setup to retest, and temps were once again a bit hotter. Re installed the ThermalRight plate, temps dropped again. Proof it is a valid product for my use case.

Amazing contact frame. Easy installation with no problems and it provides great contact allowing for great temps .

Excelente para fijar el procesador con una fuerza mas homogénea a la tarjeta madre, lo tengo acoplado a un I7 14700K con una refrigeración liquida Fractal Design y las temperaturas jamas suben ni cuando estoy jugando, lo volveré a comprar para un próximo armado

fite parfaitement sur mon i7 13700kf. Mais il m'a fallu un tournevis car l'outil donner ne fonctionnais pas avec mes vis de la carte mère pour l'ancien support. J'ai vue pas d'amélioration de température avec le frame . J'ai mis aussi du kryosheet car j'avais un contact frame maintenant et ma temperature a descendu de 90C a 80C .

Perfectly fits and very easy to install.

انصح فيه