KINLINK 8x12 Plexiglass Sheets 1/8 inch Thick, 3mm Clear Cast Acrylic Sheet, Plastic Board for DIY Project, Craft, Window Glass, Table Top, Picture Frame, Acrylic Sign and Wedding Invitation 4 Pack

I'm very happy with these cast acrylic sheets. I'm using these instead of glass in some cabinets I built, since I'm not confident in my ability to cut glass in the exact dimensions I required. Cutting these panels on a table saw with an 80 tooth carbide blade was simple and accurate, cutting with no melting and only very minimal chipping. Removing the protective paper was easy, but keep in mind that a lot of static electricity is generated when peeling back the paper, so do it in a dust-free area. The panels I received were in perfect condition, and had no defects or distortions at all. Clarity is the same as glass, or maybe even a little better. While the full 24x36 sheets had about 1/8" of defection when supported only by 2 edges, the 12x18 pieces I cut were nearly as rigid as 1/8" glass, and worked perfectly for mounting vertically in my cabinets.

I'm a product photographer and use variety of backgrounds and surfaces depending on the type and needed something that will reflect some shadows while keeping the overall surface as white as possible. The backing isn't hard to take off as long as you take a heat gun to it gently and peel it. You can tell when the adhesive is starting to loosen but if you do it this way, be careful not to overheat and melt the plastic by moving the heat gun around constantly. A cheap $20 heat gun on Amazon works more than enough and this is how I always took off any protective layers. Otherwise, you will struggle to peel this off unless you can bake this in a hot sun. A hair dryer may work but I've not tried it. This sheet is nice and thick, came without any scratches. The size is perfect for my use as well. The color is also VERY white. Whiter than some of the arctic white background I've used so this is a nice reference for my camera as well. Great quality and price!

I wanted to make a personalized birthday message for a 50th birthday cake in gold so I ordered this. It cut very cleanly on my CO2 laser and did not disappoint!!! The acrylic was sturdy and it was very shiny. It came out beautiful! The pictures don't capture how great these came out. I washed them in warm soapy water before putting them on the cake. The birthday girl loved it so much she asked me to cut her the word "birthday" so she could use it over and over again. Will definitely order again!

Good quality material in handy sizes . I cut an instrument panel out of a sheet. It cuts with a fine tooth scroll saw better than others ive worked with in the past without chipping and cracking , the hardness is just right. The only thing Id suggest is to make a solo order so it ships individually wrapped . Mine came in the same box along w a 10lb steel trailer hitch I ordered and only suffered a minor crack in the corner (not a spot I needed) after being pummeled during shipping ... Im amazed it held up 👍

Cuts very easy on laser engraver. Dimensions are close its closer to 2.8mm i have purchased this order multiple times. Very durable have used it for outdoor panels. Material is more flexible than I thought it would be but once you flex it too much it shatters. When laser cutting expect strong odors so make sure there is good ventilation and wear a respirator.

I used this plexiglass in my last project instead of actual glass and I’m so glad I did. I have been so impressed with the durability, quality and clarity. Just a note for DIYers out there: it will not cut with just a utility knife. I found the best way to cut it was with a jig saw or table saw and masking tape on either side of the cut line.

I’ve finally found a material that’s clearer than my schedule on a Friday afternoon. This cast plexiglass is so transparent I actually lost it on my workbench for ten minutes—I was staring right at it, wondering where the heck my shipment went. Once I stopped trying to find the "invisible" board and actually put it under the laser, the magic happened. It cuts with the precision of a surgical scalpel and leaves an edge so polished you’d think it was finished by a team of tiny, professional glass-blowers instead of a high-powered light beam. For engraving, this stuff is the gold standard. Unlike that extruded plastic that melts into a gooey, disappointed mess, this cast acrylic frosts up beautifully. It creates a crisp, white contrast that makes my 3D designs pop like they’re trying to jump out of the sheet. It handles the heat without warping into a taco shape, which is a nice change of pace for my projects. It’s basically the "choose your own adventure" of crafting materials—whether I’m making a custom sign or a complicated award, it just works. The protective masking is the unsung hero here; it actually peels off in one satisfying piece instead of shredding into a thousand tiny confetti flakes that haunt your vacuum cleaner for weeks. If you want your laser projects to look like they belong in a high-end gallery rather than a middle-school science fair, this is your sheet. It’s sturdy, crystal clear, and doesn't complain when you blast it with photons. Just try not to lose it on your desk like I did—it’s deceptively stealthy.

We bought these to go on wire shelving to keep things from falling through. High quality and works great.