IncuKit Mini 2 for Tabletop Eggs Incubator - IncuKit Thermostat for Incubator - Incubator Heater Unit and Fan - Digital Display with Button Control - Egg Incubator Kit

I have used incubators of all kinds over the years. large commercial units and hatchers, old metal unit, small styrofoam. A few years ago I bought a farm innovations incubator. came with a turner and candling light. Seemed good but had a heating element and no fan. The control was mediocre at best. I had some very poor results with hatches in the 50% area. This spring after a frustrating experience of controlling the heat I purchased the Incukit mini, since I was in the middle of a goose egg hatch I didn't take much time to install the kit. I am not satisfied with the way the installation looks but it is functional. The best thing I have ever bought! We had a highly successful hatch on the goose eggs with 15 of 15. I also ran a batch of chicken eggs through it. 15 of 15 eggs here as well. I believe that the almost perfect temp control along with the forced air fan providing a very even heat. Can't wait to run pheasant eggs through in the spring.

The hatch rate of chicken eggs doubled with my home-made incubator, after I installed this, replacing the mechanical thermostat system from a falling-apart styrofoam model.

Added an incukit mini heater and fan to the inside of my Epax X1-K 3D resin printer. The incukit is offset from the side and held by magnets that allow easy removal and temperature adjustment. Installed a switch on the side and plug port in the back for the original incukit plug. A segment of cable and an angled 2.5mm male jack connects the incukit to the switch and plug port inside. I can put the resin in the vat, turn the heater on, monitor the interior and ambient temp with a small accurate indoor/ outdoor wireless thermometer. Different resins have an ideal temp and high viscosity resins require the most heat for the best printed results.

5 stars since this works exactly as advertised. I will, though, be returneing this product. I just thought that 40Watts was enough for my purpose and it was not. I was trying to heat a AnyCubic Mono X 3D Resin Printer, but 40 Watts wasn't enough for my cold garage which gets to the 40s during the winter. I was able to measure only a 17 degree (F) difference between the printer and the garage before the temp leveled off and the heater stayed on without any further temp increase. BTW, I measured 52 Watts of power draw, so the heater is probably 40 watts and the fan/electronics draw the additional 12 watts. Buyer beware : check to ensure that 40 watts is enough for your application! You have to pay shipping for this item (it's not prime) so it's a waste of time & money if 40 watts isn't enough for you.

I am actually using this to heat the interior of an Epax X10 printer as the resin needs to be within a certain temperature range to cure properly. It is doing a much better job of heating up the resin in the print chamber than I expected. Very pleased.

It performs as advertised. I'm using is for my Epax x10 3d printer to keep it above 90 degrees. Setup was easy with cutting a few holes for the screws and control panel. The size of this heater is very nice and takes up very little space in the print chamber. I ended up needing to flip the fan around so it would blow the heat, but that was simple with almost no hassle at all. Overall I would highly recommend this if you are looking for a good and efficient way of keeping you resin printer at a constant temp.

I purchased two of these to use inside of some liquid resin 3D printers in order to print in a cooler environment. I cannot say enough about these heaters. They simply work and quite well at that. They are very easy to program. They retain the settings and work at those settings whenever I plug the power back on. As I get more printers for my business, so I will get more IncuKits.

Product is trash claims to be set at 99.5 but temperature stays at 103+ and they also claim Temps are adjustable but temperature doesn't move when I adjust it. And don't even bother trying to call customer service/technical support they won't answer the phone they just give you the option to leave a voice mail.

Fonctionne bien, jusqu'à ce que vous accrochier le fil d'allimentation. On dirais que ça fait buguer le controleur. À ce moment là, parfois, mais pas toujours, l'incubateur se met à chauffer et la températire n'arrête pas de monter. Ça monte ça monte ça monte et évidement c'est catastrophique pour les oeufs. Ça m'est arrivé 3 fois. Les 2 premières fois j'ai remarqué rapidement que la températire était élevé alors j'ai pu intervenir rapidement. La 3e fois je ne l'ai pas vue... Hormis ça, ça fonctionne super bien. Mais j'ai trop peur de l'utiliser maintenant.