- 3D Printer Filament, Tricolor PLA Filament 1.75mm Silk Rainbow Filament Green-Red-Blue, 3D Printing Accessories PLA Filament Multicolor, Dimensional Accuracy +/-0.02mm, 2.2lbs/Spool

Good filament with good color. A bit brittle than normal, it’s matte finish is smoother and dryer than a normal pla. Printed a lion like the one shown in the photo for an accurate color comparison

Works perfectly in the Prusa without any changes. No shrinkage and was able to create a replacement Lego piece, large sensory twist ball, and fidget spinner without any problems. The colors are mesmerizing.

Initially, when I started using this PLA, I was having issues with it sticking to the bed and printing. I was going to write a bad review (since my other PLAs were printing just fine), but I decided to do some testing and tweaking to my setup and now it prints near flawlessly! The prints come out looking amazing! Especially if you have prints with large top/bottom layers, you can see the two colors alternate with the Lines finish and it is GORGEOUS. Very aesthetically pleasing. The prints have a near-wood-like texture to them, but its generally very soft. Once you get the settings down, it prints with absolute ease. I was printing between 40-50mm/s extrusion at 205C with a 60C heated bed, and so far every print with those settings has been great. The issue I was running into was I needed to adjust the nozzle closer to the bed to get it to adhere better. Otherwise, I had cases where the filament was coming up off of the bed. Only downside to this filament (and it should be a given) is other than the occasional clog, the layer adhesion is minimal. Like these parts can be fairly brittle, so you will either need to handle with care or only print things that will not require structural integrity. For example, I am printing custom inserts for a popular board game. In my opinion, it is the PERFECT application for it. Overall, very satisfied with the filament! So much so, I bought it 2 weeks ago and I've almost gone through the whole thing with the various prints I've been doing.

Works great with my ps1 and ams 2 pro combo! I love the colors! So pretty, very durable, have had 0 issues with printing. Very durable and print amazingly. Shiny and colorful, OBSESSED. Love this filament!

This filament gets minus 5 stars for not looking anything like the picture, I'm not entirely sure if I'm supposed to use a certain black light or way of charging the "magic irradiative", I have yet to see it glow. BUT this filament still earns a positive review and recommendation, as its still looks as cool as heck, its print speed and quiality are most definitaly up to par (elegoo carbon fiber) and every print is always a different set of pretty matte colors.

Love this filament bright vibrant color good quality easy to use very good value for your money would recommend you get some prints very well no clog issues no backing up issues

Love the tri color filament. Thank you

The Good: Great looking filament, Neptune 4 Max 250mm/s print speed very happy using Elegoo Cura looks great at .2 layer even on smaller models. Could run faster. ONLY complaint is don't expect to swap in a second spool on the same print which I'll try and explain below. Tl;DR When I purchased a second spool not long after I purchased the first (a few weeks) March 2025, the color orientation was not the same so a mid print swap did not go as planned using the tri-color. If it helps to understand that visually, think of the order around the filament like a watch face starts at 12 oclock and looking at the filament at 12oclock is red. 4 oclock white, 8 oclock blue in a clockwise pattern. With tri-color if the filament is rotated while printing the color will shift on the print and look terrible depending on the design. An egg for example did not look good mid print color shifted. Back to the explanation: If the plastic is put on the spool at the manufacturer say with blue coming off the spool naturally in the 12 oclock position without you twisting/bending it you will now have blue where red was on the other spool. I tried orienting mine in the head by paying attention to where each color was but the whole batch i think was spun on reverse from the first spool I purchased so i had to start over a 5h print. Looking down from birds eye it was going red,white blue instead of red,blue,white so the red portion of the prints was good but where blue should have been was starting to print white.

Muy buen producto.. llegó en tiempo

Good quality filament. Nice colours.

We used the LOVOON 3D Tri-Colors Silk PLA filament (1.75 mm) with our Bambu A1 Mini, and initially it worked really well. The spool fit the AMS system without any issues, and the first few prints came out smooth with great surface quality. The tri-colour silk effect is impressive — the red, yellow, and blue shift depending on the viewing angle, which looks amazing on finished prints. It also arrived well packaged and vacuum sealed, which is always a plus. However, after printing more with this filament, we’ve found it tends to break quite easily. The kids noticed that it can be brittle, especially during longer print runs, which has been a bit frustrating. While the colour effect is fantastic, the durability hasn’t been as consistent as we’d hoped. Overall, it produces beautiful prints visually, but the brittleness is something to keep in mind.