VONFORN Paint Sprayer, 700W HVLP Spray Gun with Cleaning & Blowing Joints, 4 Nozzles and 3 Patterns, Easy to Clean, for Furniture, Cabinets, Fence, Walls, Door, Garden Chairs etc. VF803

Its not the same brand in the adver، returned ✋🏽. تم استلام قطعة غير مطابقة للصورة، تم ارجاع المنتج.

The rating is not really about the product. It could be great for all I know. It was advertised on Amazon UK but the device is for US users with US voltage and US plug so a non-starter in the UK.

I've used and owned other hvlp and airless sprayers before, and I am surprisingly impressed with this one, for the price. I was concerned that you can't adjust the airflow, only the fluid amount but after using it, I found that this wasn't an issue anyway. I sprayed 30 year old, painted, kitchen cabinets that had been lightly sanded and it came out as smooth as you can expect for older cabinet doors that weren't in great shape. At first, I sprayed the primer (Behr cabinet and trim primer) a little too thin. I was worried about going to heavy and getting drips and runs. but it turns out that I could have gone heavier. Then I did two coats of Sherwin Williams Emerald trim paint, alkyd enamel water-based paint. Again, the first coat was probably a little lighter than necessary but by time I put on the second coat, I did go slower to get a heavier spray and it covered very well with no runs. I did have the cabinet doors laying flat, not hanging though so that might have helped the pain level out. The paint does need to be thinned considerably. The manufacturer recommends no more than 1/2 pint of water per gallon -- I'm not sure what I used but it was closer to a 1/2 pint per quart, in order to get it thin enough. You must use the thinning funnel to test how long it takes for the paint to drain from it to make sure you have it thinned enough. I thinned it to about 50 seconds until the cup was empty. However, on the primer, I didn't thin it quite as much and the tip clogged up a couple of times and it spat out large drops of primer so had to thin it a little more. Be sure to practice if you've never used and hvlp sprayer before. Do some nice, even passes, overlapping the previous pass by 50%. Start the sprayer when it's pointed just OFF of the piece your painting and continue across and end off the other side of the piece. Do not start and stop it on the thing you're painting itself (unless it's very large, like a house or fence) otherwise it will get too heavy where you do the turn around. I'd recommend this for smaller projects: shutters, doors, garage door, cabinets, furniture, maybe a deck -- but I'd go with a much faster Airless sprayer for larger things, like a wood fence, house, shed etc. This goes slower than an airless and you'd constantly need to be filling the cup with paint to finish the project. I definitely would NOT use it to paint walls in a room, it's way slower than a roller. I'd recommend using it for a closet though, since it's more difficult to manuever a roller in a small space. It uses surprisingly little paint to get good coverage though. I used under 1 gallon to cover both sides of 27 cabinet doors, 9 drawer faces and all the cabinet faces. I was surprised that's all it used. Overall, it works great for the price but, as with anything, a lot depends on the user's experience, comfort level and willingness to learn and practice.

The device burned in my hand after three minutes or less of the first use

I was a little intimidated to use a paint sprayer at first, but this one is actually very beginner-friendly. Once you get the hang of it, it makes painting so much faster compared to brushes or rollers. The finish came out smooth and even, especially on larger surfaces. I liked that it comes with different nozzle options depending on what you’re working on. Cleaning does take a bit of time, so be prepared for that, but it’s worth it for the results. Great option if you’re doing DIY projects and want a more professional-looking finish.

I bought this sprayer to treat a new fence. It turned out to be the right tool for the job. It works like a carburetor attached to blow dryer. The smaller the nozzle, the finer the mist. The trigger turns on the blow dryer, while it also regulates the fluid flow. There is and adjustable stop for setting the maximum flow. I sprayed undiluted BLO onto cedar pickets. The smallest nozzle with the flow valve 2/3 open provide the best result. I treated both sides of an 80 ft fence in four hours. Only had to brush the tops of the boards. Clean up was an easy five minutes job. I am happy with the results.