Dual Motor Standing Desk Frame- Height Adjustable Electric Desk Legs, Heavy Duty Sit to Stand Up Desk Base, 4 Memory Settings Controller for Adjustable DIY Desktop, Over 300 lbs Load Capacity

Very easy to put together. All standing desks are going to have a little wiggle in them, but this one is pretty sturdy. I like the extra USB plug on the electric panel for charging my headphones and the extra hook that came with it for desk accessories. After a few months of use, I have had no issues with the desk raising and lowering as expected.

So far so good with no issues. Made a custom piece with a sizable piece of butcher block on top of this mount. It seems to raise and lower with no issues and is pretty sturdy. It was on tile and I had to add rubber feet to keep it from sliding around. The dual motors do a good job of raising or lowering evenly. For my particular use case I do wish the table top brackets angled into the frame instead of away from the frame so that you can place the table top to the edge of the lower footing instead of with a small overhang.

Overall for the price, it’s a great desk base. I upgraded the screws for 1-1/2” butcher block to #12’s with a 1/4” fender washer and it squared up nicely. I found some M8/1.25 x 25mm wheels to make it more portable. *Be careful of diameter. It makes the desk taller. Which in my case was fine, I’m using a high drafting type chair. Assembly was quick and easy, it squares up nicely. I mounted the legs ~ 3” in from the edges and 4” from the back edge. Drilled 2” holes for cable pass thru’s. The travel speed is fine even with the weight of the butcher block. It’s not like I’m moving it 10x a day. I’d purchase the same again if I had the need.

The product is rated for 300 lbs which gives an impression of a well priced next tier of frames. However it does not go lower than 28” because it has two part supports. Thus if you need the minimum height to be lower, this is not for you. Otherwise, Product well built and easy to assemble, sturdy, smooth and quiet. Has 4 memory locations and a usb charging port! About the only product improvement other than clear labeling about the minimum height is that the power adapter should be separate from the wall plug-in, rather than integrated as this one is, which makes it a bit awkward.

I generally don't write reviews, but I'm extremely disappointed that the motors will only move the desk with roughly 330 lbs of weight about half an inch at a time when pressing the up arrow. I removed about 40 lbs. and it still struggled, stopping after about 6-9 inches of travel. Had the press up arrow dozens of times to get it move to the highest point I wanted, set the number, ran it to lowest setting, but when pressing the number to take it to high point, when loaded, it again only moved about a half inch. Update - 07/28/2024: The company reached out to me offering a full refund, but also included some instructions. I didn't even think about a break-in period. After removing the primary glass top and the two drawers, and running the desk up and down at least two dozen times over three days, I set the 'sensitivity of anti-collision' to (0) - was (1) - and put the glass top back on. Surprisingly, it worked. The motors seems to be working a little harder, but the desk moved freely all the way to the upper set position without stopping, at a decent speed. I then added the two drawers and water bottle, and a few things that I would normally have on the desk. This time the motors struggled hard and it took longer, but the desk made it all the way to the top without stopping. I cycled it several times, and the desk made it to the top although the motors were struggling a lot. By lifting on the glass a little, taking a bit of weight off, the motors ran at decent speed and lifted the table quickly. I'm satisfied with the motorized legs, with a bit of break-in, are able to handle the weight of a 72"x30" butcher-block wood top (70 lbs.), my favorite glass desk top (70+ lbs.), 4 monitors and all the supports, and a couple of laptops and external drives, and the two drawers with misc. stuff. By lifting on the glass top, the motors run well, struggle less, and move relatively fast. I'd like to find out if the one controller could be used with a splitter to control two sets of motorized supports, (4) all together, and I'll mount the other two on the back bar, at least a foot in from the ends. Then I wouldn't have to lift on the glass, I think 4 legs should be able to handle the weight distribution efficiently, without assistance.

Easy to build. Sturdy. Effective. I got myself a birch tabletop from Home Depot for about $120, finished it and slapped it on top with ease. The result is a desk that most people would pay close to $1k for. I’m extremely satisfied

Great frame to build out a desk

UPDATE: If you’re in the market for a motorized desk and you want to buy a powerful dual motor setup, BUY THIS ONE. I couldn’t be happier even if it COST 50% more. It’s been a few weeks and this thing rocks. ORIGINAL REVIEW I’ve had it for about two weeks and could not be happier with how it works. It was packaged pretty well although one of the feet has a scratch on it that likely happened during shipping because it’s a pretty heavy box. It was very easy to put together by following the directions. Once I got it all setup I had to set the bottom limit with the buttons and it’s worked perfectly ever since. Its very quiet and smooth. Im so glad I went with a dual motor lift because I know that I’ll never come close to the weight limit of this product and since I’ll be putting it up and down a couple times a day, I hope it will last. One thing that was strange is the instructions for setting presets is wrong. It says to press and hold one of the number button until it beeps to set the preset position, however you actually press the S button first to initiate the save sequence and then select button 1-4 to save to that preset button. All in all I am very happy with the sit stand motorized lift!

la realidad que la calidad del producto es alto, muy satisfactorio, aunque realmente puede mejorar con detalles tales como por ejemplo tapones plásticos de los agujeros por donde pasan los tornillos para ensamble del marco para computadora.

Very good product and works as described

Pros: La calidad es buena, es pesado y los motores tienen buena fuerza. Contras: El problema es que se tambalea, al escribir el monitor y todo lo que tengas arriba se mueve, debido a la posición de las patas se tambalea mucho cualquier empujoncito hace que todo se mueva hacia adelante y atrás. En mi caso me vuelve difícil escribir porque el monitor empieza a moverse y marea el leer textos por ejemplo. Quise devolverlo pero tiré la caja :(

No es anticolision, entiendo que se refiere a parar con algún obstáculo, pero no fue el caso. Tengan precaución por favor.