Sealey Oil Suction Syringe 550ml Clear Plastic Body Easily remove oil Gearbox / Diff ** Sealey_AK54 **

Bought this item to assist with oil change and stale fuel extraction when servicing my garden motor mower. There are numerous slightly cheaper options on the market but this particular item is sturdy, well packaged and maintains suction for controlled liquid extraction. Oil extraction is a little more challenging due to its viscosity and requires a little more arm strength than thinner liquids but still works well. Overall it is good value and a necessary accessory for awkward oil and fuel draining requirements. Would recommend.

Bought to transfer oil in and out of a gearbox, and since buying it, it's been called into service for central heating issues, replacement of my car's header tank, a good clean out and it's good as new. Works perfectly and should last a good long time , as with most of my Sealey tools.

There were no instructions or guidance for use supplied with this device. Having read some reviews I was wary of what to expect when I got this so tested it on water before I used it to empty the oil sump on my lawn mower. It immediately started sucking air up into the chamber through the seal at the intake end plate via the threaded plastic. I tried tightening this up carefully by hand but to no avail. I then unscrewed the pump barrel completely from the plastic intake plate and found what was clearly the correct rubber sealing washer and one of a slightly smaller diameter. On inspection it was difficult to see how this extra smaller washer could have caused the problem as it was loose but I put it back together with only what appeared to be the correct rubber seal and nipped it up hand tight and it has worked fine since with both water and engine oil! I had to extend the plastic tube with a narrower one inserted as a push fit into it as the tube supplied was two wide to fit down the filler pipe of the mower but having to do this did not surprise me. The whole thing would benefit from a small shut off valve inserted where the rubber tube connects to the plastic intake end plate as there is a danger of losing the oil down the intake tube as the pump is moved sideways for the oil to be decanted. Also the ribbing on the pump barrel would allow a better hand grip if it was aligned round the barrel rather than along the barrel. I strong recommend that after use the pump is stored with the pump barrel slack on the thread of the intake end plate to prevent the rubber washer from becoming too compressed on the end edge of the barrel. When all is said and done it isn't bad for the price really and about par for the course nowadays. It did do the job, albeit after applying a life time's expertise in improvisation with this sort of thing. Like many things nowadays the issues I experienced were a classic case of the designer never having had to use his product and poor final assembly supervision. Just make sure you have a container all ready to empty your oil into before you start.

Simple idea to make your life a lot easier. I bought this to fill the transmission unit on a Kisbee with oil, it worked a treat. It saves a lot of time with trying to fill hard to get places and makes it easy to measure specific quantities of fluids. The unit appears to be quite durable and was not too expensive. another item added to my tool kit.

Unscrew the top, fill with oil and it works very well. I pre-warmed my axle and gearbox oil and that really made dispensing super easy. Great product.

Excellent well made product. Used to do oil changes on land rover gearbox and transfer boxes.

Very well made with screw-on metal end caps top and bottom. A metal piston with a proper rubber lip seal. A buffer spring to dampen the piston from hitting the end when pulling on the all metal tee handle. Graduated thick walled clear body with additional grip sleeve so you can keep a firm hold of it even with oily hands. It will pull thick gear oil slowly due to the viscosity but it doesn’t loose suction. And it’s less expensive than many of the competitor’s products .

I think the value of this item decently exceeds the money it costs. It allowed we to fill a gearbox with a filler cap on the front face from below rather than above- for the twelve quid it cost me, it saved me a lot of hassle. The build quality is typical Sealey: on the decent side of middle-of-the-road. There is more metal and less plastic to it than I expected. The plunger seal held well, sucking up thick, cold gear oil with no juddering and no air ingress. It's a tool you can make do without, but it's the sort of thing that can take the sting out of a job.

Es una estupenda herramienta, yo la use para cargar la valvulina del coche, lo que andaba buscando es y de buena calidad.

Den fungerar bra.

Hallo Habe den Saugnapf gebraucht um Wasser aus ein Rohr in 1m Tiefe zu saugen. Hat tadellos funktioniert. Der Schlauch ist sehr kurz,sonst OK. Mfg Achim

Seringue parfaite,TRES BONNE QUALITE,pratique car transparente,tres costaud,bonne aspiration,pas de fuite ni suintement.je m'en sert pour lave-glace et LR,vais en recommander pour l'huile car trop bien.Trés content et de plus,pas chere.

La siringa che ho comperato per aspirare l'olio della tagliaerba è arrivata e l'ho trovata particolarmente fatta bene... m aspettavo una versione in grande di una normalissima siringa invece all'interno di una scatola con foto e tubicino incluso ho trovato un siringone con plastica molto spessa (sembra la consistenza del vetro per intenderci). la siringa sigilla bene e ha una molla all'interno e un buchicino di sfiato aria nella parte superiore... morale della fiaba: funziona molto bene, non perde e rispetto a quello che mi aspettavo sembra veramente di qualità professionale... vedremo nel tempo ma per ora posso solo che consigliarla e dirvi che il prezzo è giustificato dal materiale di qualità.