Tap Connector Adapter Mixer Kitchen Garden Hose Pipe Joiner Fitting-BL - for Round Taps Only, 35mm MAX. Not Compatible with Square, Spray or Taps Over 35mm - Quick Connect Hose Adapter

My garden hose is connected to rainwater collection system. Unfortunately, recently the water pressure dropped to barely a trickle meaning I couldn't use the hose to wash my motorbike. I was quoted £200 to get a replacement water pump for the system, not including installation. Which is where this adapter comes in. It allows me to connect the garden hose to the kitchen tap and have full functionality. It does means I need to bring the garden hose into the kitchen, but I can feed it through the kitchen window out front to wash the bike very easily and it is not that much of an inconvenience. It is super easy to attach the kitchen tap and while there is a little bit of water drippage into the sink, it is very secure and there is no fear of it coming loose and spraying water all over the place. Very happy with the purchase and it saved me a boat load of money too.

Genius !

Well i was surprised when this arrived with no instructions. I was upset that it looked like it would be useless and I couldnt figure out how it was gping to fit to the tap. The next day I was ready to return it when I decided to look at the picture again on amazon so I could figure out how it was fitted. I tried it the following day and to my surprise it fit the tap and after a little tightening i was good to go. I connected the other end of my hose (which already had a connector on it which came with the hose) and it worked!!! I was amazed that it worked so well. I use it on a small sink which is in my toilet near the back door and the sink is very shallow. My only problem is that there is not enough depth in the sink to allow the hose to hang freely so it sometime bends sharply as it hits the base of the sink. With a little innovative manipulation i can slightly lean the hose. This has nothing to do with the connector but more my sink. My tap has a squarish end but the device is to be fitted under the hole that the water comes our of on the tap. You can tighten it to make this fit more snugly and then pull down the lever to tighten this connection.it is a good little gadget that says what it promises. I wish I had bought this sooner, so far so good!

I have a water-bed and I wanted a simple way to connect a hose to one of the bathroom taps, for topping up the bed from time to time. I have an old adaptor with a frame that fits over the tap like this one does, but it has a threaded rod that screws down to push on the top of the tap-spout (like a cider-press). It is only a small diameter and if the tap spout is not flat, it was difficult to get it mounted firmly and without leaking. It has a soft-rubber seal that mates up against the water outlet on the underside of the tap, and over time this has become cut and distorted, and does not seal well. This new adaptor has been excellent. I have been able to use it successfully on taps both with a flat top to the spout and a curved top. To install it, first back-out the lower section that has the hose quick connect, and lift the orange flap. Then slide the adaptor over your tap and screw the lower section in until the whit seal is lightly touching the water outlet on the lower side of the tap. Lower the orange flap. And screw the lower section in a little tighter. I tested it quickly by turning on the tap before attaching the hose. If it leaks at this stage, turn off the tap. Lift the orange flap, and tighten the lower section 1/8 of a turn more. At the same time look closely at how the white seal is aligned to the underside of the spout, make sure it is flush. Lower the flap. I have found this to be quick and simple to do. It has taken me much longer to write this than to actually do it and get a good seal. Note: I have seen some other reviews mention that they crushed their tap with this device. I can see how that could happen if you tighten the lower section against the tap to the maximum that you possible can, and THEN lower the flap - the leverage via the cam could be enough to crush the tap. It does NOT need to be tightened so much (mind you, some cheap modern taps are quite thin and fragile). If you are seeing leaks, look at the alignment and do not blindly tighten the adaptor. Once you have finished, and closed the tap, lift the flap and back off the lower section 1/4 to 1/2 a turn. I am very happy with this adaptor. Edit 19 April 2020: I have used this adaptor now almost 10 times. After the first two, I can now get this on a tap and aligned so that it does not leak, at the first attempt. Still very happy with it.

This is the only one that fits onto lever taps, I tried the screw type adaptors,but the lever was in the way so water turns on before connecting properly.This adapter fitted great and was easy to use

Absolutely brilliant peice of kit,no more leaks,highly recommended

I bought this item because I was assured by the Amazon robot that it would fit our average-size bathroom basin taps. It doesn't. When fully screwed up, this device falls about a quarter of an inch short of where it needs to be to touch the spout of the tap. I will not be returning the gadget, though, as it does fit our kitchen mixer tap.

Packaging & Build Quality The product arrived in simple black plastic packaging. While there were no additional attachments, I already had compatible parts from previous kits, so this wasn't an issue. The adapter itself feels surprisingly sturdy. It's made from good-quality material that doesn’t feel flimsy or prone to breakage, reassuring for something used so frequently. Installation Installing the adapter onto my kitchen tap was straightforward. I didn’t encounter any difficulties, and it fits snugly with no need for extra tools or accessories. The universal design seems versatile enough for most standard taps, and it integrated smoothly with my garden hose. Performance The most important aspect of this adapter is how well it performs, and it certainly met my expectations. I tested it at full water pressure, and there were no signs of leaking around the tap. The tight seal it provides ensures that water flows directly into the hose without any wastage or splashing. Pros: Durable Material: The sturdy build gives me confidence that this will last through many uses. Leak-Free Performance: No leaks even when the water is fully switched on. Easy to Install: Fits well with no complicated steps involved. Good Value: Given the quality, it feels worth the price. Cons: No Additional Attachments: While it worked for me, having extra attachments might be useful for people without compatible parts already. Overall Verdict This Universal Tap Connector Adapter is an excellent choice for those who need a solid, no-fuss solution for connecting a garden hose to their kitchen tap. Its durability and leak-proof performance stand out, making it a great addition to your home setup. Highly recommended for anyone looking for a reliable and affordable tap adapter!