Rollerhouse Rechargeable Wireless Tubular Roller Shade Motor Kit, with Remote Control for Motorized Electric Roller Blind Shades, 1.5 inch Tube

I was a bit apprehensive buying this given the varying degrees of difficulty people had reported. My experience was surprisingly simple. I was ready for cutting, grinding, and fabricated yet didn’t need to do any of that — the motor fit perfectly inside my tube, and the extra bracket assembly kit had an end plate fit perfectly on my existing brackets. I was able to take down my roller blind, insert the motor pulse end plate, and had it reinstalled in ten minutes. Here’s what I did1. Carefully measured my tube. It was 38mm2. Confirmed with seller the right motor to buy given my tube diameter and the metal tabs on the tube3. Bought the motor kit AND the mounting accessory kit. The accessory kit was mandatory for me to have the right end cap that would work with my existing brackets.4. Charged the motor battery5. Removed metal valence and popped out my roller blind. One end of my blind is a push pin and the other was the chain drive6. I pulled the chain drive out of the tube. Took a little force but it popped out7. I inserted the motor into the tube, rotating the motor so the rubber piece on the end aligned with my tabs on the tube. The motor slid in8. I made sure the charge port was facing down for easy access9. I found the end cap in the accessory kit. The black end cap whichworked with my existing brackets.10. I screwed the end cap in with the two screws. Many said the screws were too long. I didn’t find that to be the case11. I put the roller blind back into the brackets. The push pin allowed me to get the blind into the space while i worked on getting the end cap hooked onto my bracket.12, I tucked the antenna wire around back of the blind so it didn’t get clipped by the valence.13. Made sure the power port and remot program were facing down where I could access them14. I pressed the program button on the motor. It jogged twice. and then the c button on the remote. Roller and remote were now paired. And I could raise and lower15. I realized the motor direction was going the wrong way with remote. Pressing up caused roller to go down. Followed the instruction to reverse the motor direction. I held the limit button and stop button which reversed direction. Now remote worked correctly16. Programmed upper and lower limits per the directions17. Everything working flawlesslyMy test case worked and I ordered six more. Will update when done with the project. But so far…a big success and huge improvement to having the chain drive for so many rollersEdit:I ordered six additional motors and installed each. I did not run into any problems. Followed the sequence from above and all seven motors are programmed and workingI also purchased the 15 channel remote and linked each motor to the single remote. I can now control all seven from one remote with each window being on its own channelNext I purchased a BroadLink rm4 pro to connect the motors to an iPhone. I configured the BroadLink and added each shade to my hub. Bin each case, I went through the process of having the BroadLink learn the remote codes. And ultimately programmed open, close, and stop buttons. Now I can control each motor with my iPhone through BroadLink. I subsequently linked groups of shades to a BroadLink scene allowing me to control multiple windows at once. Even cooler was BroadLink allowing me to pair with Siri. Now I can say open living room shades and a block of four shades opens. Couldn’t be happier with the outcome. Have another five kitchen windows that I would like to automate in my next round. And my project will be complete.

I had an old Smith and Noble electric Roman shade where the motor failed. This was a perfect replacement and was easy to install. Worked with my existing remote. Saved a lot of money since I did not have to replace the whole shade. Great that battery is rechargeable. No more changing batteries.

This motor is excellent; it has been a lifesaver. A while back, I bought some zebra blinds for a large door, and I got this motor to operate them; it has turned out to be a wonderful surprise. It works perfectly, and the battery life is incredibly long—it doesn't need to be plugged in constantly.

I received two of these motors yesterday, and it took me maybe 20 minutes to figure out how I was going to adapt these motors to the Rollease tubes. All it took, ultimately, was a little work with my Swiss Army Knife to trim a little rubber off of the drive wheel so it would go into the tube. The plastic bushing on the proximal side of the motor fit perfectly and required no adjustment. Then there was the job of trying to figure out how to program the motor reading the instructions obviously written by someone not a native speaker of the English language. Also, the instructions showed a different remote than what comes with this motor. Note that the confirm and limit buttons are inside the battery case. This was the most difficult part of the installation, due to the poorly written and erroneous instruction manual. Ultimately, I figured it out and programmed the first motor. Then I had to do the second. However, when programming the second motor, I the remote affected the first motor and messed it up. There is no power switch on these motors, regardless of images here that aren't the same as the motors I received. So, I had to remove the second motor, reprogram the first, then have my wife walk down the road about 250 yards with the first shade to where it was no longer affected by the remote and program the second motor. Now they both work perfectly, but I bought these as a trial because I have 4 other shades I want to replace. However, my wife can't be walking back and forth with 5 shades! So, unless someone can say how to program one motor without affecting the others, I'll just stick with these two for now.

The device works but is very noisy. Since noise indicates wasted energy I suspect this will lead to problems eventually. I purchased these hoping the most expensive on Amazon would be of higher quality. I purchased a tuya blinds motor on Ebay 8/2022. It was a little cheaper than this and a little quieter however the batteries failed in 2024. I should have spent the additional money to purchase rollease blind motors from ebay. I purchased one from a local blinds company. It is very quiet and is still working two years after purchase. I was penny wise but pound foolish.

Used this with 1.25" schedule 40 pvc pipe to wind up the strings on four 70" roman shades. Works great.Had to buy the brackets and end pieces seperatly, but it all went together fast. I had a good plan that I had been working on so I was more than ready for the DIY part of the project.Black rubber drive wheel had to be filed down to fit in the 1.25" pipe. So did the spring loaded end bracket with the cross looking end button. Again, no big problem there either.Used a piece of poplar wood to hang each of the shades, brackets, and tube/motors on.Then I used SHORT screws to secure the strings to the pipe so the screw tips didn't damage the LION batteries inside the red tube. I also measured and put two screws through the pipe into the black rubber drive wheel to prevent slipping. This is all so the strings roll up onto the tube which is raises the roman shades.I'm using it with the 5 channel remote. Easy to program and set the high/low limit/stop functions. Motor direction is reversable using the remote to program. Very versatile.Easy for a handy person with a plan.Works like a champ! My Wife is stoked that I was able to complete it so fast and that it works so well. Great alternative to buying four new 70" shades at $700+ each!

Very easy to install and work exactly as they should. Much cheaper than the local blind shop wants to charge to convert my existing shades to motorized...$100 vs $1000 because they insist they can only build new ones. Make sure you're ordering the correct size....they are usually referenced by the OUTER diameter of the tube, not the ID. I did have to change the rubber inserts to match my tube, but it was very simple and all the parts were included. I had to modify my bracket a little to fit into the slot in the motor (filed down from 1.5 cm wide to 1 cm wide...next time I'll order new brackets at the same time. Instructions for pairing the remote and setting the limits are usable, but obviously not written by a native English speaker. If i didn't have to modify the bracket/hangar, I probably could have installed them in about 15 minutes each by myself. I will be buying more once I figure out a suitable solution for a gateway to my smart home controller.

I had purchased blackout roller blinds for a set of three large windows, but the roller stops didn't work well, and I wanted to try and automate them using this product.I bought one first to try it before going for all 3. Experimenting with how I was going to install definitely saved me time for the other 2 installs.I reused only the shade material from my blinds. I purchased 1 1/4" EMT tubing from a local home improvement store as I couldn't find aluminum roller tubes that weren't overly expensive for the sizes I needed (nearly 4' and nearly 8'). One question was answered through my install, this combination of the 1.5" motor did work OK with the conduit with a few minor modifications.-I cut the tube to size using the fabric as my width guide-Using an exacto knife I carefully removed a small amount from the black rubber piece so it would fit into the tube better. I tried to remove only what I needed so it wasn't jamming in as this is the piece that actually turns the tube.-As the conduit doesn't have any internal ribs, I drilled a small hole and inserted a nail into the rubber piece through the tube to prevent slipping (the seller recommended this). Measure the location and drill before you put the motor into the tube.-I also shaved down the plastic fins on the idler bracket a a little using a box cutter.With these modifications I was able to adapt and get the motor in the tubes.I purchased the brackets sold by the seller which worked well.Programming the remotes gave me a little trouble until I realized that you need to EXACTLY follow the sequence of setting the up and down limits, IN ORDER as written on the instructions. Once I did this it was simple.I purchased the 5-channel remote from this seller so all blinds could be controlled from one remote.The seller was extremely responsive to my questions with the product during the whole process. That was great and totally helped me out.Had I stopped here I still would have been very satisfied at the ability to automate a whole wall full of window blinds for around $400 in all (including the conduit and a few other supplies).As the last step was I purchased a Broadlink RM 4 Pro on Amazon, installed the app and "learned" the roller blind remote function. With this I can create routines and automate raise/lower times. (The Broadlink only will control raise/lower, you need the upper/lower limit setting from the Rollerhouse remote.) As others said in the Q&A, 433.92 is the frequency to use. I haven't yet integrated the Alexa part but apparently that is possible. Now all 3 blinds raise and lower in unison at my preset times.Totally worth it!!

Je voulais motoriser mes stores enrouleurs et après avoir longuement regardé mes différentes options en terme de difficulté de mise en oeuvre et de qualité/prix, j'ai finalement choisi Rollerhouse.Lors de ma première commande, ils ont immédiatement pris contact avec moi afin de s'assurer que le moteur tubulaire était compatible avec mon installation, puis m'ont envoyé le colis.Le moteur a été très facilement installé, sur un store légèrement plus grand que la recommandation. Et depuis +- un mois, tout fonctionne à merveille, du coup j'en ai recommandé un second :)!Bref très bon produit, je recommande..

A little noisy, a touch bit slow, but works every single time and exactly as you want it to. Nice looking remote with optional wall mount, single channel.Comes with adapters to fit different style roller blinds but diameter must be correct.I did not use a smart device with it although it says I can buy a hub for it to use with an echo.Follow the Instructions in order. When setting the top height, bottom height, and middle height, you might think the instructions are separated into sections for what you need to program but they’re are not. they must be programmed in the order on the instruction manual. The way the manual is written is not a mistake.

Ho dovuto adattarlo perchè il tubo della mia tenda non era da 38mm ma da 25 e il motore non poteva entrarci.Avevo quindi chiesto la restituzione.Il venditore mi ha dato alcuni spunti per provare a usare il prodotto e devo dire che mi è stato utile, ora la tenda è automatica.PS: le procedure di inversione dei comandi (alto/basso) e di set del minimo non sono proprio intuitive... dovrò tornarci sopra o tenermi la tenda in manuale.

Usado para un estor de 40mm sin ningún problema. Fácil de colocar, no se aprecia en absoluto y llevo varias semanas subiendo y bajando varias veces al día con la primera carga de batería. Fácil de configurar y enlazar con su mando. Muy cómodo y recomendable.Edito: 3 años después de colocarlos siguen funcionando a la perfección y las baterías las habré cargado 3 o 4 veces, dando un uso constante a diario. Sigo encantado con el producto

Money saver if you have old blinds with cords and want to upgrade it. Easy enough to install but kinda had a hard time doing the limits on the remote but that’s a me problem. Will definitely buy more for our other old blinds. Don’t know if there’s an app you can set time to automatically open and close blinds, that would be cherry on top.