EZDIY-FAB GPU VGA PCIE 8 Pin U Turn 180 Degree Angle Connector Power Adapter Board for Desktop Graphics Card-Standard Type 2 Pack

Have been using these on my 7900gre in a corsair 4000d rs frame case and they made cable management super easy and tidy as I ran my cables along the top of my gpu. Looks clean and so far no issues after a couple of months. Make sure you get the right orientation for supreme fit on your gpu as durability comes from proper connection.

The EVGA RTX 2070 graphics card in my primary PC requires two power connectors, a 6-pin and an 8-pin. Bending the wires to connect without adding too much stress to the card, plus routing the cables back to the PSU has always been a pain. When I found a SFF (small form factor) build video on YouTube that used these adapters I ordered them immediately. They connect easily to the card, and the connection to the power cables has a positive click to ensure they're seated. Routing the cables is so much easier, there are no sharp bends required, the cables are straight into the adapter. These are available in both 6-pin and 8-pin versions - the 6-pin adapters have both a standard and a reversed connector in the package. The 8-pin adapters have two of the same orientation in the package, so make sure which ones you need - the pictures clearly show which way the pins are facing, so you can determin the right option(s) for your graphics card. I don't review many purchases, but wanted to note how useful these EZDIY-FAB adapters really are, and how much value they provide for their cost. I'm truly suprised video card manufacturers don't include these in their packaged accessories, they are that useful. Super great product, I'm going to buy these for every PC I work on going forward.

Exactly what I needed to keep GPU cabling at bay. This relieved the cables free of stress from unnecessary and sightly bends. It fits snugly into the GPU and also not difficult to remove if needed. It’s perfect for what I needed it for.

Since PNY does not sell a similar part, I found this part for my new PNY GeForce RTX 4070 12GB XLR8. I purchased this part due to I had a similar part when I owned a EVGA GeForce RTX 2070 SUPER FTW3 ULTRA GAMING, which was a EVGA PowerLink, that moved the cables to end of the card. This makes the look of the setup look clean. I had this part on my card while running on Starfield with High settings for many hours and had not had any issues for more that a 4 days so far. I will updated my review IF I run into any issues.

The adapter worked well, until it melted. I've since since photos of melting nearly identical to mine. Yes it was fully seated and in a stable (non-mobile) desktop. Fortunately the intermittent ground connection caused the GPU to crash whenever I started a game, so I went searching for the cause and found the melted adapter before any serious damage was done.

The EZDIY-FAB 8-Pin 180 Degree Angle GPU Adapter are great connectors to help with cable managemnt on yor PC case. These adapters appears to have a very good quality and they fit snugly on the 8-pin port. They are supper convinient and easy to install, allowing you to route PCIe power cables without bending them and helping with the case aestetics Just make sure you get the right ones by checking the GPU 8-pin connectors. There are "Standard" and "Reverse" 180° adapters available and they are compatible with different graphics card models.

I'll be short on the review. I like the look these 8pin 180 angle adapters give to my build, and there's no power or thermal issue in the connection between the cables and GPU's 8pin ports. Mine only question/complaint to the seller, who is supposedly the manufacturer, is why you sell pack of two of the standard type while you, also, sell the reverse type in pack of three? It is very inconvenient to buy several packs of standard type for GPU that has 3x8pin ports. Honestly, feels like a money grab...this is mostly the reason I gave 4 stars.

There are great they look good and do exactly what they say. I would agree that they need to figure out a way to make them clip to the video card connector as they can push themselves out. That will not be a problem for me though as I have them put in in a way they should not come off the card. The system in the picture is how it currently looks but is not in a finished state. I plan to have the power cables to the video cards connected to the video cards and off the back plate. At least with this picture you get an idea of what it looks like when they are in place. I will buy these again as needed in the future.

These u-turn connectors make the build a lot neater compared to the stock cables that run everywhere. You should get the right ones for your PC.

Plug and play.

Exactly as described

Tested these with a multimeter to check the pin continuity and all of them have continuity with each other which should not be the case! They should be 1-1 and any crossing or sharing of pins should be managed cable-side. TL;DR THIS PRODUCT WILL FRY YOUR PC AS THE PINS ARE ALL SHORTED TOGETHER