Bully BBS-1103 Truck Black Powder Coated Side Step Set, 2 Pieces (1 Pair), Includes Mounting Brackets - Fits Various Trucks from Chevy (Chevrolet), Ford, Toyota, GMC, Dodge RAM and Jeep

These things came with a ton of extra stuff for connecting to many types of vehicles. The installation for mine was pretty straight forward I did not need anything other than a couple bolts and screws. The spacing/or distance apart for making the holes was straight forward also. The issue that I had was lining the hole up from the edge of the lip. I found that I had to expand the initial hole a bit on each because of the difficulty of the line up and the tightness of the location for placement. I also had to go buy myself some lock washers because none are included. Overall this was a very easy install and they are very sturdy, I come in at a couple pounds under 200 and these things hold just fine. Worth the money and the small amount of hassle with installation. I needed a drill with the proper bits and a Philips screwdriver or drill bit and a socket set. Additionally I needed a Dremel to expand the holes in the truck to line up properly but if need be you could use a hand file.

Very sturdy and it comes with all the hardware you would need regardless of truck type. I have 2009 F150 and had to drill new holes for installation. It was a pain and took about 2.5 hours due to poor drill bits and what felt like iron pockets in the steel. In the end, they are worth it because my daughter and short family members can now comfortably get in and out. As a bonus they look good too. When I decide to replace my torn drivers seat these will definitely help prevent me from tearing up the new one. Worth it! But definitely have good drill bits on hand and measure twice. (I used a dremel with diamond burr to elongate the holes because they were slightly off, worked great). Hole pattern 9/16 from edge and 8 & 3/16 center to center on the holes.

First the good. The steps are very well made and were not difficult to install. The steps are well worth the cost paid. Now the bad. As other reviewers have noted, the included hardware is worthless garbage. The first bolt sheared in half with a small amount of force with a socket wrench. The first phillips head metal screw's head was stripped upon attempted tightening. I immediately switched to better hardware that I was lucky enough to have at the house. My recommendations for others during install. Only tighten bolts to a snug fit. The smallest bit of torque will break them in half. If your application calls for the phillips head metal screws, make your pilot hole one size bigger so that you won't strip the head, or better yet, use a bolt head screw. I would have given 5 stars if not for the hardware.

I needed a "step up" on my 4WD F150 and took a chance on this product. What a life saver! The older I am getting the more I needed this product. It's a simple single step that doesn't detract from the appearance of my truck. It works great!@

Absolute garbage. I haven't even finished installing the 1st one, but I'm so frustrated buy the product quality and horrendous installation instructions. Quality - Not installed and already chipped. Small bubbles or voids in the finish have already chipped off and exposed bare metal. Installation is turning out to be a nightmare. 4 holes drilled thus far and I've only just got them to line up side-to-side. Instructions say 8 1/8" between holes, but they are 8 1/4" apart. As to how far in from the edge of the panel that you need to drill, its kind of up in the air. IF you are going to purchase these, make a template (yes, NO templates included). Make the template from real measurements, not from the instructions. Get a paint pen to make where the panel edge meets up to the step when its firmly seated. This will give you a reference as to how far back from the edge to drill your holes. As I said, 4 holes and not a single fastener in yet. My panel is looking like swiss cheese. I don't now know if the panel still has enough integrity to carry a load. Wish I would have known that installation was going to be hit or miss. I would have started on the passenger side, which rarely gets used, to hash out a game plan. I will be sure to steer everyone away from Bully products.

Ordered these for a 2025 Ford Ranger and they would not fit without extensive modification. Seems like a quality product if it fits

They were a perfect fit for my 2002 F150 Supercrew FX4 and easy to install. Made from solid cast aluminum and a nice black powder coat. They look great on my truck.

Sturdy and versatile, easy application. I'm 270 and I have no fear stepping on these.

Doesn’t fit or compatible with Grand Cherokee 2009 as mentioned by seller.

Die steps hatte ich in 30 min angebracht. Die Installation ist mehr als einfach. Beim Chevy Blazer K5 Bj.78 überhaupt kein Problem. Ohne irgendwelche Adapter oder Passhülsen zu verwenden. 8 Löcher bohren , anschrauben - fertig. Hält bombenfest.

Todo está bien. Buena calidad y precio.

Nice product. Going in is easy and these work well but coming out you must be able to judge where step is and place foot in.which at my wife's and my age is rather difficult for her. So if your older don't get these go with long side step. If your younger you will love these steps Cause I do

Passt