WALI Tall Monitor Arm Mount for Desk for 13-34 inch Screens, 22 lbs per Arm | Single Extra Tall Monitor Mount, Full Motion with Tilt, Swivel, Rotation, VESA Mount 75/100mm,for Office/Home (M001XL), Black

This monitor mount is heavy duty! Sturdy, well built, and can mount two different ways. I have a keyboard stand with an upper shelf. I installed the monitor mount using a center slot I had cut into the shelf and it was a breeze installing it. My video monitor is small and I wanted it just above my music rack which sits toward the front of the shelf. I have a video system combined with my keyboard so I can watch movies while practicing. I highly recommend this monitor pole mount. Great value for the money. Monitor can be moved in a plethora of positions.

The Wali Single Monitor Desk Mount works better than I expected. First, the basics. The mount comes well packed and the instructions are very simple to understand. There is so little assembly required that the instructions are almost not needed. Assembly and installation can be done in less than ten minutes (not including cable management if you choose to use that feature). Adjusting everything is easy. Overall quality of the parts and the assembled product are quite good. I have two monitors that I wanted to mount on a flat desktop. I needed to be able to get the monitors right next to each other and still have the desk flat against the wall. Most double monitor stands will not allow for this unless your monitors are the perfect size for the spread of the arms. The movable arms will usually flex toward the wall if you want the monitors to be edge-to-edge with each other. The result is the desk having to be offset from the wall to accommodate this. By using two single monitor stands, I am able to move the posts to positions that allow the arms to be extended in such a way that everything is flat with the wall. The other frequently stated issue with most monitor stands is that the arms have hydraulic pistons and/or springs to deal with the weight of the attached monitors so they are easy to move up and down. These pistons and springs are often of poor quality and either fail quickly or don't work as expected from the get-go. This is not a problem with the Wali Single Monitor Desk Mount. The arm is solidly attached to the 16" pole and only moves up and down by loosening the arm mounting and sliding the arm up or down on the pole. The arm, once set to the desired height, can be move forward, backward, side-to-side and tilt. This makes for a much sturdier setup with no pistons or springs. This system works very well, since I (and I think most people) have little need to move a monitor up or down after the initial installation. I leave the included Allen wrench stuck in one of the vertical facing screws behind a monitor so that it is always handy but out of sight. If I do need to move the monitors up or down, the tool is right there. I will buy two more of these for my wife's desk.

Trying to arrange multiple monitors on a single desk is usually never an easy task, even less so when your desk is against a wall, in a cove, and/or just has limited space in general. When I made the transition from YT content creation to live streaming, I felt a need for a third monitor... as I already had two monitors (side by side) on a dual-monitor desk mount, but I had no more room to expand (horizontally)... I could only go UP! After searching through all the monitor stands over and over again, I ultimately decided on this WALI "Extra Tall" mount, and I'm glad I did! Not only is it more sturdy than the dual monitor mount I had already owned (even with just one monitor on it), but this one is much TALLER, has a considerably longer arm, and I don't have to tighten down all the bolts once I get the monitor in the position/orientation I want it to be in... like I do with the dual monitor mount. That one, I have to loosen the bolts, move the monitor, then tighten the bolts... otherwise it sags, tilts, rotates... etc etc. The WALI mount though, yeah... it holds the monitor exactly where & how I want it! Currently it is only holding an older 27" Acer monitor, which also happens to be an 'nVidia 3D Vision" monitor... which were exceptionally heavy monitors for their size! The arm is secured near the very top of the pole in order to have that monitor above my primary larger 32" monitor, and is slightly tilted down/at me. It doesn't wobble, it doesn't drift, the arm articulates easily enough, and it doesn't even sag when I extend the arm outward all the way! It simply does what it's meant to, and it does it well enough that I'm replacing my dual-monitor stand with another two of these. (They don't sell the arms separately, so I have to buy 2 additional mount kits in their entirety. I plan on using just the arm from one of them to add to the pole I already have mounted, and then I'll use the 3rd kit in it's entirety for the 3rd monitor.) Why do this if I already have my 3 monitors mounted to my desk? One, the WALI mount is much more sturdy! Two, the WALI arms are almost twice the length of the arms on the dual mount I currently own. Three... again, I don't have to mess with the bolts every single time I want to make even a tiny adjustment! The WALI mount is just... better in every way! Sturdier, longer, easier to adjust, and less pricey!

For the price, I’m pleased with it. Overall, it’s a sturdy stand with quality machining. All the screws went in easily, poorly machined products have crooked holes or bad threads. The mount base comes with 2 types, standard mount for a desktops surface. The other one is for desktops with monitor holes/cabling drilled through them. All the parts are heavy gauge and I encountered no difficulty during assembling. There seems to be a tension screw for the tilt feature. I had to tighten the screw that holds the tilt joint together because out of the box, the monitor flopped forward hard. I had to be mindful while mounting it to the main arm so it wouldn’t slam into my glass desktop. The 2 arms that allow you to move the monitor forwards and back, left and right were a little stiff, I loosened the screw a bit on the main arm, at the pole. That seemed to be all that was required. I tried to loosen the bolt where the 2 arms meet, and it wouldn’t budge. I didn’t force the issue. The instructions were adequate for assembly without covering anything else, like adjusting the tilt bolt for the weight of the monitor. So, while I think this was a good mount for the investment, there are tradeoffs to mention. I’m accustomed to swinging my monitors upward and dusting underneath them. Height is fixed by a screw on this one. I was struggling to install the monitor cables when I realized you can tilt the bottom toward you until the top or the monitor hits the pole, or, until it’s sitting nearly flat like a table. Elevated several inches above the desktop. I consider this a Pro / Con feature. Where the arm ties into the VESA mount, the fit is a little sloppy. It’s not a safety concern but I can wiggle the monitor backwards and forwards at the outer edges “About ¾ inch “before feeling any resistance from the mount. Same goes for tilting. I don’t see this as much of an issue. Normally, I don’t foresee any outside forces acting in the monitor to create a problem. However, there’s room for improvement. The rest of the machining seemed steller. I have multiple computers in different rooms. 32” monitors are used as primary monitors with 32” to 23” as secondaries. I like mine roughly 1” above the desk. That places the top of the monitor at my eye level and the ideal viewing angle. I have fully articulated, hydraulic mounts on most of my monitors. Nice ones for large heavy monitors run $75 to $100 and up. I paid $36 for this one. The……… WALI Monitor Arm Mount for Desk, Single Extra Tall Computer Desk Mount, Monitor Bracket Mount Stand Single, up to 32 inch, 22 lbs (M001XL), Black. Amazon lumps the reviews of similar products together, so I specified which mount I purchased. I’m using this one on a glass desktop, I’m attaching it to the same point I constructed from wood for a different mount. It didn’t lower the monitor low enough either. So, the top of that mounting point is 4” lower than the surface of the glass top. Despite being that low, I didn’t actually need the 32” pole / monitor mount, the 16” model would have worked. There’s still 2” of pipe available above the arm. The 32” was on sale & I didn’t know if the 16” would suffice. The pole is a screw together 2 piece. I unscrewed / removed the other pole as it looked out of place in my dual computer setup. That leaves a hole in the top of the pipe / mount. I wish they included a cap for that. The top pipe has a cap but of a different diameter. I’d like to give it 4 ½ Stars but Amazon won’t let me. I’ve got to go with 4. Height adjustments with heavy monitors and an Allen wrench can present a challenge, it’s the nature of the beast and I won’t give it 5 stars for a few reasons. The sloppy VESA mount and loose tilt motion. No instructions that cover that, or if I was supposed to loosen the arm at the pole to improve motion. I would recommend this mount to others.

I wanted a mount that worked with a desk grommet while still allowing cables to go through the hole, would work on a narrow (22") desk attached to the wall without making my monitor stick out past the front of the desk, and was under 20" tall so it would fit under the overhead cabinets. This mount hit all of the marks! Installation was fairly straightforward. The only issue I had with the whole install was that the VESA mount screws were a tad too long, leaving the bracket a little less than snug. I grabbed a couple spare washers from my garage, and I was back in business! I like that I can lock in the height (have to tighten it with the allen wrench, but I don't intend to move it often), the arm articulates well, and it supports rotation. I also like that the VESA mount is in two pieces, which allowed me to mount it to my monitor and then slide it into place on the arm, securing it with a cap nut. It feels secure, AND I get to recover the space underneath the monitor (and permanently evict the dust bunnies!) I paired this with a small rectangular USB 3.0 hub, which I was able to zip tie to the arm, allowing me to hide all my peripheral attachments. The included cable management is simple and does the job. Super happy with this purchase!

Since my 50" monitor is under the 22lb weight limit, I decided to give this arm a shot. Nobody seems to make an arm for something as big as a 50-inch even if they don't actually weigh that much. So what happened? The arm CAN support that weight and size. The manufacturer did a great job on the materials and it assembles very easily. For a regular monitor, this arm should work great. But the clamp design is not exactly sturdy enough for my bigger screen that exceeds the intended use. Clamped to the table top alone, the pole had a serious and unsafe lean to it. I ended up reinforcing my table with three layers of plywood secured with lag bolts right through the table top. Between the layers of plywood is the table top and a steel beam that the table top sits on. So this is a ridiculously strong base. With that in place, the arm does hold the monitor in the fully retracted position. Extended, there is way too much leverage and the arm starts to lean. So don't do that. It needs to stay totally retracted to the pole. To fit my monitor, I had to get VESA extension wings and those worked fine. This provides the solution I am going to use: angle irons bolted to the wings and running down to the table. I have room to do this. The angle irons will take up most of the weight and let the arm stay vertical and let me move it around. So it will be a three-legged mount instead of one. Eh. It will work fine for me until I come up with something better. Very tempted to drill holes in the clamp base and lag bolt that to the table. Nothing is going to beat that except welding it.

I recently purchased an LG 32UN500 monitor weighing ~17 lbs. The included monitor stand was not great according to the reviews so I opted to purchase another stand. The WALI would take the load and it appeared solid. Assembly was straightforward. I opted to put a hole through the desktop for the stand. The monitor came with its own screws for the VESA mount so I used those. Once assembled I adjusted the arm height and tightened the arm to the stand so it would not slide. I then placed the monitor with the attached VESA mount in the arm mount and attached the nut to secure it all in place. Adjustments are easy with the supplied Allen keys. The stand allows me to tilt, swivel, and raise/lower the monitor height. Solid product that does the job it was designed to do at a reasonable price. Adjusting the height does require loosening the fastener so if that is required frequently you might consider another stand. One last point, the attachment to the desk requires so little space that I have regained all the space I lost to the stand for the previous monitor.

This is the monitor mount I should have had all along. The extra tall pole allowed me to mount my 32" monitor at the correct height (something I couldn't do with the spring-mount I previously had. It came with good directions, everything needed for install except for a Phillips head screwdriver and a 10mm wrench for one cap nut. The arm that holds the monitor is highly adjustable, and once everything is tightened down, very sturdy. I recommend this one without reservations.

43インチモニターを購入し、 高さが欲しかったのでポールの長い本商品を購入しました。 翌日配送できましたが、到着して開封してみると本商品はポールを2本連結させるようなのですが1本しかはいっておらず返品しました。 型番を確認すると M001XLと製品ページではなっていますが、届いたのはM001SXLでした。

Bought this to hold 32in monitor above imac 27in, does the job and very good quality.

Good product

This is great - all metal and very solid. It’s probably not as adjustable as others, but for the price it’s great value and works best for a monitor that won’t be moved often.

You can buy cheaper items than this but the arms sag. This is solid as a rock. My only caveat is that if you should want to return it because you have changed your mind you will end up paying the postage back to the States! Also note that the pole on these items has a larger diameter than some other makes so beware if you are adding extra arms etc.