ELEGOO 8K Water Washable Resin 8K Space Grey 2000G

Looks great after washing and curing. I really like the water-washable resins and this one doesn't disappoint but it is the first time I'm trying an 8k resin and so far it seems to capture details really nicely, although as of the time I'm writing this I'm still dialing in my exposure settings but so far it's about 2s per layer at 0.05mm on my Mars 4 Ultra and it's still over exposed so the settings in the listing are a bit high at least for my machine and area but other than that it's a pretty great resin (Sorry, no pictures yet as I'm still dialing in the settings)

It has a good consistency, the minis i did were detailed and came out fine just have to be wary of thin walls since this isnt abs like. Clean up without need for alcohol is nice and reduces some smells. Supports shater on plate as they adhere to good and reducing initial exposue lend to some supports not adhere corectly to plate. Solid 9 out of 10. Got this for free from the mars 5 ultra purchase.

Don't let the picture deceive you. I wanted to post it to warn people that it might happen, but also wanted to sing the praises of the product. This is the second bottle of the Clear Red resin I have purchased, and it is an excellent resin. It has a slightly stronger odor than the Solid Gray resin of the same type, but the prints come out beautifully. My second bottle arrived damaged. However, thanks to the packaging it arrived in, the liquid was all contained inside an air-tight bag, and funneling it into my old bottle was a piece of cake. The bottle could possibly use a bit of reinforcement on the lid to prevent this in the future, as it seems that section of the lid may be a weak point in the construction. Included is a picture of some minis that I've printed to show off the clarity of the resin. These were printed on the Elegoo Mars 2 Pro. (Camera's not stupendous, though) TLDR - Product is excellent, moderate odor, good clarity after printing. Bottle has a glaring weak-point, but packaging around it is air-tight baggy, so no problem.

Overall I would have to say I liked this product. It shows wonderful details in the finished product, easily washes off under water, and has a is low odor when printing. The viscosity is great and I had no problems on models I vented and supported properly. The only downside I have found is that it is a very brittle product once cured. Small pieces can easily snap off. When used for printing miniatures (my primary use) the smaller details are often the most crucial.

I am new to resin printing. I have had a FDM printer for a long time now. I was concerned for a long time about dealing with the resin. The cost of having to have a lot of alcohol on hand, the odor, and keeping everything clean was concerning to me. Decided to try the washable resin to see how it did. I was initially concerned that this would be inferior to regular resin and although easier to deal with, would create worse prints or be more fragile than regular resin. I am glad to say my fears have been unfounded. The prints so far have come out fantastic and with great detail. I have had a few issues, but that was due to support layout (learned my lesson about using the autosupport function in my slicer, it isn't close to enough supports). The cleanup has been a breeze with just water. I also got a small ultrasonic cleaner. Works so great with just plain water. I found that a 3 step cleaning process gets all the lose resin off. I use a pickle bin first to rinse it right from the printer to get the heavy stuff off. I swish it in basket for 10 seconds or so. I then remove the supports and put in the ultrasonic cleaner and run that for 4 minutes. I change the water and run again for another 4 minutes. After that I let air dry and then cure when fully dry. That process took some trial and error. My first prints I just washed in the pickle jar and was getting a heavy white powdery stuff on the print. Did some googling and determined I wasn't cleaning enough. I then used the ultrasonic and it got better but not perfect. That is when I did the second wash with clean water and then fully air dried the pieces before curing and now I get perfect prints with no powdery stuff on the outside. I also don't have to do a lot of manual scrubbing that I don't have time for. I figure the cost of the ultrasonic cleaner is definitely offset by the fact that I don't need any isopropyl alcohol at all. Which is good because that stuff stinks up my shop when I use it. Speaking of odors, the resin does have a slight odor. You can smell it and it has a distinct odor, but I don't think it is strong at all and so far has not been a problem which is good because I can be sensitive to odors. With the lid closed on my printer and the bottle closed, I don't smell anything. Only when pouring new stuff in the vat do I smell something and then it quickly dissipates.

I’ve been extremely impressed with the Elegoo Water Washable 3D Printer Resin. The print quality is fantastic, with sharp details, smooth surfaces, and consistent results across multiple projects. What really sets it apart is the convenience of being able to clean prints with water instead of dealing with large amounts of isopropyl alcohol, making post-processing much easier and less messy. The resin cures well, has excellent dimensional accuracy, and I’ve experienced very few failed prints when using the recommended settings. It’s also great for detailed miniatures, functional parts, and display pieces alike. For anyone looking for a reliable, beginner-friendly resin that produces professional-looking results while simplifying cleanup, I highly recommend Elegoo Water Washable Resin. I’ll definitely be purchasing it again for future projects.

These resins have beautiful color to them and look good solid or hollow, though the solid models do look better. I've printed in the smokey black, green, and blue colors and I'm very happy with all of them! The water-washable aspect has completely changed my printing habits. Using IPA in the past was a major headache and annoyance. With the water-washable, I can simply put about a gallon of hot water in a tub and use a toothbrush to clean up the miniatures. Rinse them off in another small tub of cool water, then place in front of a fan to dry off before curing. The used water can then be left outside in the sun for a few hours to cure the washed-off resin. Strain the water and toss the cured resin. Easy peasy and no spending $$$ on IPA and dealing with fumes, storage, etc.

I've been using this resin for years now and it's consistently great. Prints come out clean and great detail. It can be a bit brittle if you over cure it but that's pretty standard unless you want to invest in some high priced resin.

Funcion abien con mi impresora

No failed prints, No after prints problems and most of all the printed parts fits and no shrinkage. I'm ordering 2 more of 1KG of this resin as of writing this review. I never imagined I will be happy printing in Black colour and the after print is in Matte not glossy. Perfect!