WEN BG4286 3-Amp 8-Inch Slow Speed Bench Grinder, Orange,black

Very high quality grinder, well-built, easy to assemble and the slow-speed makes sharpening easy. Pair with a sharpening jig set-up for repeatable grinds.

Wonderful grinder. I only had a slight problem with it. I bought it for sharpening lathe tools, and when I replaced the fine abrasive wheel with an expensive diamond one, it wobbled. I replaced the stamped cup washer that came with the grinder to hold the wheel on with a machined washer, and bingo, wobble gone. It runs very smooth, and the bearing are so good, it takes minutes to stop. I really like it!

It’s worth every penny’s . This low speed grinder is worth to buy I installed CBN sharpening wheels on it and it works flawlessly . It has power to do all my sharpening and the low speed kinds are the best to go for it . It comes with grinding wheels 60 g. And 120g. Also some small jigs to attach to it and magnifier lens . Well priced and it works great .

I just got this and set it up. The wheels seem to be turning fine with no wobble. Managed to get the pieces assembled with no issue (after I oriented myself). The instructions are ok, it was me. It fires up smoothly. It does take a while to stop spinning after it is turned off, just for reference. Also, and I think this is an issue with most any grinder, accessing bolts or screws to secure the unit on a bench can be a challenge due to close quarters. You may need to be creative. But I figured out a solution in my case so life is good. I've typically seen good reviews of Wen products so didn't really hesitate to pick up this grinder. I intend to use it for sharpening lathe chisels. The grinder is definitely heavy so I don't expect to get much issue with vibration. There are rubber feet as well.

Bought this slow speed bench grinder for sharpening my wood lathe tools. It does the job but does have some wobble on start up and shut down, even from very start up without sharpening anything. Everything is tight, but guess the wheels are out of round a bit. Gets the job done.

This is a great product. I see that there are complaints from some about the grinding wheels. I can't speak to that as I use high quality CBN wheels mainly for sharpening HSS turning chisels. If your plan is to use CBN wheels, I think you will be happy. Very smooth.

It perfectly sharpens my wood lathe tools, axes, knives, scissors, and drill bits. It is well-built and quiet. It comes assembled except for a couple of things which are easy to attach. It has plenty of power and is big enough to do anything I want, yet small enough to fit in my small wood shop. Plenty of bang for your buck.

Bought this knowing it wasnt going to be top of the line and would have its quirks. But the wheel does not spin straight. A lot of wobble. The tool rest also will not sit square making it impossible to get a good grind for sharpening anything. Even if buying aftermarket tool rests or making your own it is useless because the wheel wobbles quite a bit. Disappointed and a waste of money in my opinion. Didnt expect it to be the best but it should at least spin true.

A solid piece of equipment.

Excelente esmeril. Incluye dos piedras de óxido de aluminio blanco de 8", una grano 60 y otra 100 y sus bajas revoluciones hacen que el acero de las herramientas no se caliente, evitando el destemple.

Très bonne meule mais pas mal plus grosse et lourde que je le pensais, surtout que je vis en appartement. Mais je l'ai gardé et elle m'est très utile. Si c'était à refaire je m'en trouverais une plus petite. Mais parfait pour les gros bricoleurs.

Llega mucho antes del tiempo que marca, excelente cuidado al empacar, a pesar de ser un producto muy pesado, no me llego con ningún tipo de abolladura o desviación.

Excelente calidad ideal para afilado de Gubias para torno