Printhead Cleaning Kit for Epson, 250mL Printer Cleaning Kit for Inkjet Printer, Print Head Cleaning Kit for HP, Print Head Cleaner for Canon Inkjet, Printer Head Cleaning Kit 250mL for Brother Inkjet

Very easy to use and very effective! Simplified directions for an effective cleaning: 1. Go into your printer menu and have it start a print nozzle cleaning. Be ready to disconnect the power immediately after it starts. 2. Unplug the power once the nozzle cleaning begins. This is important, it stops the printer head from moving and keeps it in an unlocked position. 3. While the printer head is unlocked and the power is turned off, remove your secondary printer cartridges (if equipped) from the movable printhead. Mark each one to help remember the order they go in! 4. With the secondary cartridges removed, you should see 4 little nipples/ports corresponding to each color cartridge. 5. Grab a few paper towels and fold each one 3 times, lengthwise. Place 1 folded paper towel into the tray beneath the printhead assembly to help absorb the mess that is about to come out from it. 5. Use the cleaning kit with the hose/tube FIRMLY attached to the syringe and fill the syringe with the cleaning solution. 6. FIRMLY attach the other end of the hose/tube from the syringe to the nipple/port on your printer and begin applying pressure to the syringe plunger to eject the cleaning solution into the port. Once the syringe is empty, carefully disconnect the hose/tube from the print nipple/port and dab it clean on a paper towel. Now you can refill the syringe and repeat the procedure on the same port to ensure it is cleaned. 7. After the second flushing, slide the printhead over to remove the paper towel beneath it. (It is going to be a soggy mess.) Take your second paper towel to replace the one you just extracted. 8. Repeat steps 5 and 6 (and 7 if necessary). 9. Once you have cleaned all of the ports, dab up any spillage from the bottom of the printhead before you reinstall the secondary cartridges and remove the paper towel from beneath the print head. 10. Reinstall the secondary printheads making sure they go back in the correct order or your prints will come out discolored and odd looking. 11. Run 2 or 3 print head tests on fresh paper to verify the printer is working correctly. It may take 2 (in my case 3) times for this test to complete properly with freshly cleaned ports because it needs to flush out the residual cleaning solution from the ports. 12. Enjoy your Like New printer!

Great product and it does that's supposed to do. My Epson ET 3850 stopped printing magenta color completely and the yellow was starting to go next. As a result everything I printed looked horrible even some black and white items. The kit comes with everything you need although, I didn't use the gloves that came with it since they were too loose in my opinion - I used my own. So I did a thorough clean starting with the magenta and yellow; 4 times each a total of 20 ml each until everything loose clear. Then I cleaned the blue and black, 2 times each a total of 10 ml each, since I didn't want to go through it again. Make sure you keep everything nice and clean and dry and constantly replace the paper towel to absorb all ink. Afterward I didn't a power clean and voila the printer is back to normal printing beautifully and I still have plenty of cleaning solution for future use if the problem occurs again. I didn't use the instructions that came with the kit but instead I used a YouTube video specific to cleaning my epson which was slightly different and a lot more helpful. The whole thing was a lot easier than I expected and didn't take long. Plus it saved me a lot of time and money. All on all great product!

this worked great! I have an EPSON 2850 that has been converted to sublimation and so ink tends to get a bit clogged. Usually if I run a few sheets through it, the clogs flush out, but this time I couldn't get my black to print at all. I ran print sheets through, did head cleaning, etc. but it didn't improve. So, $10 for a chance this might work, seemed like like at better idea, then pitching the printer. The process was super easy (there are some good video's on YouTube on the "how". Watch a few of them, but don't fall for the super expensive kits; this one works! Running like new!

Nice cleaning set that was exactly as described. It worked well but did not fix my printer problem.

It was a bit difficult to figure out access to my inkhead, even after watching their video, but that's not their fault. I have ten minutes of intense fear after I did the cleaning, because I'd paused overnight and didn't notice there was still a sheet of paper in there. Teasing out all the soggy bits used up my quota of luck this month, so RTFM TWICE and doublecheck yourself. Assembling the syringe from random bits and forcing the silicon tube onto the ink stub was not easy. Good fingers, a hemostat or fine plier, and bright light are needed. Not easy. Not fun. But once I got it all done (and undid my paper jam mess) the printer fired up. Didn't tell me one color was out (as opposed to still clogged) but once I found that, eureka! The damn thing is printing again. I used two full syringes, after 6 "head cleanings" still hadn't purged the black, fwiw. I think the full kit would give you one full cleaning, 1x on all four colors. But for me, the black cart is the devil incarnate. If I don't print for three weeks...goodbye. Bottom line? This worked as claimed. Saved me from buying a new printer!

Sadly, failed to work with my C88+ Epson printer. I love the printer, one of the few that works with particle based inks which are the only ones that are water resistant. On the other hand, the printer is approaching 12 years old and has been reliable for that time. Epson appears to be phasing out their water resistant inks and it's hard to find a replacement.

Compatible with my Epson MF-3720. Black was really gummed up and not working. It took a few times of forceing the fluid through with the syringe, at first just back flushing until it let go and statred flowing through. Ran a test sheet, good again! I cleaned all 4 just for good measure. All the fittings, the extra fluid I have for next time. All a bonus, making this well worth every penny. Easy to use, instructions included. Got rid of my clog.

I followed the written instructions and watched the video for cleaning my HP 9730e, and brought a dead printer fully back to life. You have to be patient and have to follow the instructions exactly, but the result is a clean print head which allowed me to resume printing both b/w and color. I recommended this to a friend who is an IT specialist

100% work product super quality

منتج ممتاز جدا (اشكر البائع)

After i didn’t use my printer for couple of days , it wasn’t able to print in colors and black. I tried to fix the problem by deep cleaning option but it didn’t fix the problem at all. I decided to buy this kit and thankfully i did. I followed Youtube videos tutorial and finally the problem is resolved. I highly recommend this kit if you want to revive and clean printer head.

الجودة

Ita scam,i have order th printhead solution kit,i have received a half used bottle thats it nothing else package already opened.