Question 1

how do you hang the mount?

Accepted Answer

A manual and install guide comes with each station. From the specs: To ensure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supporting significant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meets ADA regulations when properly installed.Drilling holes and mounting the station:1. Remove changing station from the shipping container and check for any freight damage. If damage is found, please call Koala Kare Products' Customer Service. Remove "Installation Kit" and "Operator Kit" from box. Please give "Operator Kit" to facility manager or operator. Box should contain two pieces: the bed and metal mounting chassis and the wall mount liner dispenser. Identify the best location for installing the unit.2. Standard Installation- Remove the bed and chassis from the box and select the wall area where the unit will be installed. Make sure you have taken into consideration the operating clearance of 9½" (241.3 mm) on both sides of the exposed chassis and 22" (558.8 mm) from wall surface when open. Measure from the floor 44¼" (1123.95 mm) on stud center and mark the wall. The mounting holes are designed for 16" stud centers. Ensure the locations you have marked for the mounting holes are level before drilling. Drill pilot holes for keyhole mounting using a 1/8" regular drill bit.Masonry or Tile over Stud Wall- Use a 7/32" (5.56 mm) masonry drill bit for the pilot hole until you hit the stud. Change bit to 1/8" (3.18 mm) regular drill bit.Metal Stud or Concrete Block- If the wall has wood studs that are not on 16" (406.4 mm) centers, has metal studs or an underlying surface of concrete block, drill with a ½" (12.7 mm) masonry bit. (You may have to purchase toggles before installing.) You must allow a minimum of inside wall space for toggles to turn depending on toggles used. Insert and tighten toggles.3. Screw two of the mounting screws into the pilot holes leaving ¼" (6.35 mm) exposed to allow keyhole slots to be easily mounted over the screw heads. Place chassis over screws. After securing the unit using the keyhole slots, verify that the unit is level. Tighten top two screws so that they are flush with the wall. Use the four lower holes as a guide to mark and drill pilot holes. Use remaining four screws and four washers to complete installation of bed and mounting bracket. Insert washers over lower four screws. All SIX screws and four washers must be mounted to the chassis.4. Ensure liner dispenser is free from damage. Remove key, unlock, and open liner dispenser lid. This will expose liner dispenser mounting holes. Line up dispenser mounting holes onto chassis and secure with the four screws provided. Close and lock the liner dispenser door.5.Clean work area and inspect unit to ensure it opens and closes smoothly. Give Operator Kit and key to the facility operator.The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. The manufacturer reserves the right to, and does from time to time, make

Question 2

Is this model a wall surface wall mount ?

Accepted Answer

This model mounts to the surface of the wall.  However, you will have to find studs in which to screw securely into wall.

Question 3

The key did not come with our package so we are unable to open the liner holder area to hang the table on the wall.  Can we please have an extra key?

Accepted Answer

Call Amazon customer service to request key copy.

Question 4

Is any other color? I’m looking for cream finished color.

Accepted Answer

You can purchase this unit in a variety of colors including cream (KB200-00), Grey (KB200-01), Earth (KB200-11), and white granite (KB200-05)

ASIN	B00OGIB5E2
Brand	Koala Kare
Colour	grey
Customer Reviews	4.7 4.7 out of 5 stars (525)
Global Trade Identification Number	00893145002486
Is Assembly Required?	No
Is Extendable	No
Item Dimensions	10.2 x 81.1 x 52.7 Centimeters
Item Type Name	decal
Item Weight	28 Pounds
Manufacturer	0
Manufacturer Part Number	KB200-01
Model number	KB200-01
Number of Items	1
Number of Packs	1
Shape	Irregular
UPC	749628417462 640206811224 641438389222 636123964518 638084700525 781264201678 642125311397 726983202896 787766399257 893145002486
Unit Count	1.0 Count

Koala Kare KB200-01 Horizontal Wall Mounted Baby Changing Station, Grey

Details

Details

Description

Specifications

Common Questions