POE Combiner Splitter Adapter, Run 2 IP Cameras on 1 Cable, Works on all POE Switches, POE NVR and POE Cameras, Mode A and B POE Compatible

I bought one about six months ago after researching. Then bought a few more! Was a little unsure with the first one if it would work initially, given the power draw by two devices. But it has a switch for two types of wiring, good just in case! And I used the higher power PoE+ switch that was 802.3AT compliant. PoE switches that are only 802.3AF compliant don't put out nearly as much power on the line. So make sure your PoE switch is 802.3AF (PoE+) compliant. May work with one that's only 802.3AT, but I wouldn't try it to find out unless you already had one there. The better PoE+ switches aren't expensive. I had a PoE wired Ring cam, but wanted to add a Reolink PTZ camera about 15ft from the Ring cam that was also wired PoE without running an entire new cable. Easy to install, and both devices powered up and connected without any issues. Still running without a glitch 4 months later. So if you were going to use it to connect say two Ring or similar PoE cameras, it would have no problem with it as I'm fairly sure the Reolink PTZ cam pulls more power than the Ring cam with it's auto tracking. I wouldn't experiment with cheaper PoE splitters. This one is well engineered and won't let you down.

They work as described, 2 poe cameras on one cable

I had a buried line running in conduit to a tree for a camera and realized, I could eliminate 2 others from my house if I had another one in the same tree....IPCamPower to the rescue! Worth the money vs. time/effort to run another line. Initially, only 1 of the ports was active, but flipping the switch for that port fixed it. I'm assuming my cables are not as expected. I was VERY happy when it worked. I highly recommend it. It seems well-built and the instructions are fine...really, plug it in and go. If something is not working, try flipping switches (1 thing at a time, also make sure the cable you're using works, etc..). I had a bit of a tough time cramming all of the cables and the adapter into the junction box. I could have left it all out in the weather using the included caps. I'm very pleased. I see no loss of signal over the 2 cameras now running over the 1 cable. Power is good. I didn't measure anything but the video is perfect from both cameras. I'm running an 8MP and 5MP Foscam camera with no problems.

I had a wire that went bad (water intrusion fouled the pass through connector). Being the cameras were next to each other facing opposite directions, I installed this and worked perfectly! I did try it as well on a longer run I have out of curiosity and it was not enough to power two cameras over 250 feet away. I installed a switch and split the feeds that way to supply power to each camera as It would only supply one feed not two. But for price and if it’s a quick fix or permanent install they’re super easy to install!

I picked up this IPCamPower PoE combiner/splitter adapter for my Reolink cameras, and it worked exactly how I needed it to. Everything connected cleanly, and it handled both power and data without any issues. Setup was straightforward—plug it in and it just worked. It’s been reliable so far with no dropouts or power problems, which is really all you want in something like this. Overall, a simple but very useful piece for a PoE camera setup. No complaints.

The concept is good haven’t tested the quality yet but there are two major design flaws with the waterproof caps which makes it useless for my project 1. The rubber gasket is not split so impossible to fit around a finished wire, which makes it completely useless for me. 2. The end cap that you would screw on to the prong end the diameter is way to small which makes it physically impossible to use with a finished RJ45. making the waterproof concept completely worthless for me to use. This company’s product department must revisit their design flaws as it prevents the concept of a waterproof/ water resistant system. Picture a picture speaks 1000 words pictures attached to demonstrate their product versus industry standard. Really wanted to love the system however without manipulating a $20 set you would like you shouldn’t have to cut widen the caps for it to work. One would think this should have been thoroughly thought through but it wasn’t. The end of the RJ45. Don’t even match the identical version that I have which has the rubber coverings for the plastic clip. I really needed and wanted this to work, as I had to finish my project today. Its now not going to happen as it can’t work for my outside POE system. I would not recommend this to anyone wanting to waterproof/water resistant their system.

Product works amazing, had a 2 camara run where one of my 2 cables went bad, instead of running a new cable, just put this on the good cable and whalla, back in action, used with an REOLINK system, no issues. Left the dip switches on the factory setting with no issue.

Worked exactly as advertised with LTS cameras and NVR. Very well made.

I hadn't heard of devices like this "IPCamPower POE Splitter Kit" before. I've recently upgraded from an 8 channel NVR (using POE), to a 16 channel NVR with POE. The only down side to that upgrade is running the cabling for the extra cameras. I bought this kit hoping it would work, and the good news is it does perfectly. You plug the splitter/ combiner? (with the switches on it) into the two channels on the NVR you want to use, then run the single cable from it. Then plug the other splitter cable onto the end of that single cable. Then run the two cables to your cameras. I used B mode on the combiner end as suggested in the instructions. After the splitter at the camera end, I've got one camera on a 5m cable and the other on an 8M cable- they work fine, even the POE.

شغال ممتاز

Potwierdzam, że działa z kamerami i rejestratorami Zintronic / Herospeed. Zwykłe rozdzielacze nie działały.

Purchased for our home security cameras. I had no prior background with installations and found these were easy to set up! We have 4K cameras - the video/image quality appears unchanged when using these. Perfect for what they are for!

よく分かりません。 poe電源から5m先に1台目のｶﾒﾗが有り、そこから分岐して3m先にもう1台追加でｶﾒﾗを取付たら1台は読込みますがもう1台は全く読み込まない、 カメラが悪いのかと思い接続を変えても変わらない。 LANはｶﾃ5e、B結線。ｶﾒﾗは既存と同機種。 poe電源付近で2台接続したら映る… 離れると映らない…？ 調べても外国産なので細い説明は無く 自宅使用なので考えるのは辞めました。 ｺﾝﾊﾟｸﾄで良いと思買いましたがちょっと残念。