Sculpt High-Temp Resistant 3D Printer Resin, Clear, 1kg | Thermal Resistance up to 180C, High Precision, DLP LCD Capable, Ideal for Engineering, Jewelry & Industrial Use

Sculpt ultra is one of the most amazing resins I've used and really shows the trickle down of material science to consumer level printers. It barely absorbs any water or solvents and is incredibly rigid. It's very ceramic like in many ways, probably because it IS filled with ceramic particles. It's a bit difficult to print, bed needs to be leveled just right and more importantly, because the resin is so opaque, the z-height needs to be very small to not have bed adhesion issues. I had a ton of issues until I realized that was my problem. Whenever I level my bed, I then set the zero a couple steps down and everything is good. The prints come out very smooth and because it's so brittle, the supports come off the cleanest of any resin I've tried. It also means you can't drop your prints as it will shatter like glass. Highly recommend for specialized use cases where you need high chemical, wear and heat resistance.

This is very brittle, but you cannot beat the temp resistance. I mix with a little tenacious flex to make it a little more durable. Overall, this stuff is great.

Came very quickly products works as described but had to search through forums to get the best advice on how to use most effectively.. otherwise it’s a very strong resin and it’s use case is as described.. if you are making vulcanizes rubber molds I strongly recommend coating the model with a mineral oil. This helps prevent fracturing of the surface which can leave lines in the wax and gave my team our best finish.

An extremely good resin for 3d printing items that need heat resistance. I used this to make a bracket that went on my VR headset to hold a face tracking camera. The headset gets hot enough that even FDMA printed materials warped over time. This resin however did not warp, ever! it also seems to have far less shrinkage than other resins. downsides: it is sensitive to printer temperature, make sure you have a heater to maintain 25c while printing. it's also very brittle so don't expect much flex from it. lastly the ceramic particles in it are harder than metal so it's not wise to use any kind of blade to remove support material.

I used the 80% Siraya Tech Sculpt High-Temp Resin with 20% white Tough Resin I had on hand to make new sockets for a tube preamp I am refurbishing. . I did some tests with 100% Sculpt but when I did my offline temperature tests, it withstood the heat but the thermal shock from getting hot and cold quickly caused the thin areas to crack. By mixing with some tough resin, I was able to make a part that has held up to the ~100C temps without cracking. The pictures show the before and after the the tube/socket replacement. I will definitely be using Siraya Tech Sculpt High-Temp resin for future projects. By the way, it printed flawlessly! (I use a heater inside the chamber set at 90F.)

This is my fourth time using this resin. It's the only High Heat resistant resin that doesn't cost an arm and a leg to buy. There are other "Engineering" grade resins but they cost almost double the price. Not only that but those other resins come in proprietary containers meant to fit specific 3D resin printers. This Ultra White resin prints to very tight tolerances in my X1 printer. I'm presently working with lead casting. I'm working on perfecting my airgun pellet molds. These pellet molds still need some work to optimize my work flow but right now I can honestly say I'm on the right track by using this particular resin especially since I'm pouring into them some molten lead with temperatures of up to 750 degrees Fahrenheit. If not done properly the introduction of this amount of heat into my tiny pellet molds can and will ruin them in pretty short order. There is a set routine that must be followed not only for safety's sake but for successful cast as well. Be safe everyone.

This resin is total crap. Have yet to have a print that doesn’t fail. I have tried every printer setting possible and printed the exact same part using several other resins without any difficulty. I tried heat, I tried long exposure, short exposure, everything in between yet every print failed. Mercifully we are almost done with the entire 1000g bottle and will not be purchasing anything from this company again after this dismal experience. I wanted a thermally resistant material for use in a high heat application, and this product sucks so bad I never even got a single print to finish successfully. I will search for superior alternatives to this waste of time, materials and money. You have been warned.

Simplemente excelente calidad, a un buen precio, tiene componentes cerámicos que sirven para aplicación de temperatura y químicos, por lo tanto hay que tener en cuenta que es muy dura pero también quebradiza (cómo cerámica)

I was warned this is tricky to print with, but apart from ensuring the temperature is kept to a minimum, it seems no more difficult than anything else I’ve used. I had one initial failure, mostly because of my rush to place supports, but have since printed several items with no issues. Good detail and exceptional dimensional accuracy. I cannot fathom why, but I also use less of this resin for the same models printed with another product. Weird, but good!

Résine épaisse, super pour faire des moules pour injecter de la résine, résistance à la chaleur au top. Une super marque.

ideal für gussformen die Temperaturen bus 160 Grad aushalten müssen.

Me ha Sorprendido su resistencia. Utilizar en ambiente ventilado. Y gafas protección para luz ultravioleta. Seguir los consejos del fabricante.

This resin is very easy to work with in contrary to some comments and video clips found online. I use Chitubox and the profiles available from the Siraya Tech site are very helpful. The pictures show some prints for my FDM printer and I'm quite satisfied with the result. Now hoping its HDT property is up to it claims.