10000011 Speedy Seal 2 - Universal Heavy Duty Tire Repair Kit For Car, Truck, RV, Jeep, ATV, Motorcycle, Tractor, Trailer. Flat Tire Puncture Repair Kit Fix Punctures and Plug Flats 50 String Plug

Unfortunately, as with most merchandise, the ARB 10000011 Speedy Seal 2 is Made ("manufactured") in China, but in accordance with the design specs by the Australian company. The manufacturing origin is shown on the cardboard sleeve cover for the tool case. This review is given prior to use of the tools. However, this is not my first time to "plug" a leaky tire - in this case a screw puncture. With that in mind, having used plugging tools in the past, the ARB 10000011 Speedy Seal 2 is definitely good quality with weight, irrespective of the manufacturing origin. The tools are not "junk." One thing I would point out is to CHECK the torque on the Allen Set Screws before use, particularly for the plug "insertion needle." Mine were slightly loose when delivered, which is fine since this is a good manufacturing/assembly protocol. One tip for anyone who has never plugged a tire: If you have access to an electric (or cordless) drill, remove the handle on the "reamer" tool and set it firmly in your drill. Use a slow drill speed and work the reamer in and out of the puncture hole a few times to make a clean, round hole. Also follow the angle of the puncture whether it is a "straight-in" puncture or at an "angle." This makes the job much easier. Another tip: It's not so much the tools that determine the success of the plugging. There are two parts to a successful "plugging." First, good tools and good adhesive/plugs. Those are the two components. Some plugs come with the adhesive on the plugs. Rather than using the "lube" with the kit for the "insertion needle," I prefer applying adhesive on the tip of the insertion need and on both sides of the plugs (full length) after threading the plug into insertion "eyelet" needle. This will act as the 'lube' and also will give additional adhesion. I ordered (separately) the "Western Weld" clear vulcanizing adhesive (Made in the USA) to use with the plugs, I have used this with 'plugging' projects in the past. It does what it's suppose to do; hence, the "Weld" in it's name. One last tip: Apply the adhesive liberally to the puncture hole entry before inserting the plug. When inserting the "insertion needle" to plug the puncture, go straight into the puncture all the way to where the sleeve on the shaft is firmly against the tire tread and flush against the handle - then rotate the handle one-quarter (1/4) turn and then remove the insertion needle. After removal leave about 1/4" - 1/2" of excess plug sticking out from the plugged puncture hole. Air up the tire to recommended tire (PSI) pressure. Apply more adhesive on the plugged hole. Let the tire set for about an hour to allow the adhesive to dry. Then use a soap/water (sudsy) mixture to check for air leaks. No leaks... Then you are good to go. Finally... Check the tire pressure on the vehicle every one or two days for about a week or two. In my experience I have never had a tire to leak. That is just my own personal experience. Hope this helps...

Now this is a quality repair kit with all metal tools, no plastic handles here! Old school👍

I won't rehash all the glowing reviews about this sets' superior construction and content. I will say that both its handles survived multiple whacks with a drive hammer and survived. It is billed as a "4x4" repair kit for off road tires, but will also work quite well on passenger car tires. So here's my experience with a few pointers to make things easier. First after you gather all the tools, lube, cement (more on this later), pre-thread the rope plug through the needle, making sure you have 2 even length plug 'legs' bent upwards towards the handle. Locate the puncture, pre-lube the reamer and have at it per the instructions. You really will have to twist and drive the reamer past the tread belts. Although you can repair a tire on the car, you need so much leverage to drive the reamer, (and the plug needle) through the tread and tread belts, it will be difficult. I would estimate 50-75lbs of arm pressure is needed to push through. The tougher the tire (i.e. LT type tires with a lot of tread), the more you will have to push. Here's tip # 1; take advantage of the removable handle on the reamer (hex key supplied with kit), and attach just the tool shaft to your electric drill--instant ream job! Just don't overdo it! Now that you've rounded and trimmed off the puncture all the way through the tread, cord, and belts, use the reamer as a 'plug' to stop any additional air from escaping. Things go better with air pressure in the tire since it supports the tread around the 'target area', so don't let the whoosh of escaping air rattle you. Next, remove the reamer. Air will escape, but if you have about 20-25 PSI of air pressure left in the tire, you will have plenty of time to grab your loaded plug needle and put it in the hole. My first repair was rear tire on a sports car. Very limited working space=very little leverage. I could not drive home the plug. Tip #2. The solution was to coat the plug and needle with rubber cement(purchase separately as it is not supplied)(disclaimer: I think this was mentioned in a previous review-thanks). The cement acted as a lubricant, and while still difficult, I finally was able to drive the plug home. In my case, the kit-supplied lube was ineffective. It probably would have been different if I removed the tire however. Note: This is an "open eyelet" kit. The plug 'needle' has a open slot to facilitate its removal from the tire whilst leaving the plug in place. DO NOT rotate the needle when driving the plug into the puncture. You risk spreading/breaking the eyelet off the needle shank within the tire, or jamming up the eyelet with the twisted plug. Feel free to drive the plug all the way into the tire until the sliding cone stops your motion. NO fear of going too far. Put pressure on the sliding cone, holding it against the tire, while pulling the needle out. The plug is now perfectly seated in the puncture. Just trim the leftover exposed nub with a blade, leaving about 1/8" excess above the tread, so it can be further seated by the rolling tire. One final point, you really need to carry, or have access to, an air compressor or air pump to re-inflate your repaired tire. Otherwise driving on a severely under inflated tire is inviting a blow out. Like everything else, this kit has it's limitations. It probably won't work if you have impaled a railroad spike as you cannot 'double up' the plugs. Also, side wall repair is out-too much flexing. Same with angled punctures. However, when done properly, the self vulcanizing plugs should last the remaining life of the tire. Happy plugging!

I put this set to use this week. Went off road and get a small puncture on my jeep. With this kit that my sin had, we were able to plug it fast and clean. Had me worried as I was 40 miles from any help. Like my son said, buy the right tool the first time, never buy a replacement after. I took that to heart and bought my own. This kit works great and is well worth the cost when out and about.

Over the years I have had several of the cheap tools bend the shanks when trying to shove a string seal into a small hole in tires. Its frustrating. I bought this set and the steel shanks must be made of good steel and hardened properly so they do not bend. The grip handles are nicely designed and fit in the hand really well when pushing hard to get the seal into the tire. The blow mold case is ok and typical of asian cases with latches that are light duty and subject to breaking if snagged on something. I'd like to see a better case and another pocket to keep small tubes of rubber cement in. I prefer the rubber cement as a lubricant and sealer over the grease lubricant provided in the kit that works ok too. This is a quality kit.

This kit is perfect for the do-it-yourself'er and to fix puncture flats in the field. If you know what you're doing this will be a piece of cake. Some quick tips to help when repairing your flat tire are: 1st tip. Partially inflate the tire to create some rigidity in the tire to aid with inserting the rubber plug into the hole otherwise the flat tire will flex as you apply pressure to insert the plug. (Assuming you have a tire inflator) 2nd tip. As you attempt to insert the lubricated rubber plug into the hole you just reamed, remember to slighty rotate the needle handle itself clockwise and counter-clockwise. This slight rotating motion will aid with inserting the rubber plug. If you try to insert it with direct, straight force, you will have a lot of resistance to fight against. Note: Remember to apply pressure on the handle only along the length on the plug insertion needle. Any sideways pressure and u risk bending the plug insertion needle just like another reviewer did. That's entirely user error. I've repaired puncture flats on a new car tire and the plug repair lasted the life of the tire(60,000 miles) so rest assured a proper repair will last. I carry this in my trunk at all times and highly recommend it.

I don't think there is anything special about this kit, but I am happy with it so far. It has easy-to-follow instructions. The tools seem sturdy enough. The case that comes with it fits nicely in the compartment under the floor of my 2007 Mazda3 hatchback. It takes some muscle to actually insert the plug into the tire and then extract the tool. If you are plugging a puncture in one of the vehicle's front tires, you can leave it on the car, but I can't imagine repairing a rear wheel while it's on the car. You wouldn't be able to find a good position to put enough force on the tool. I took my time and probably spent an hour fixing one of the front tires of my car just now. In comparison, I could have easily spent two hours at a tire shop and they probably would have conned me into buying a new tire. Therefore, I would estimate that this kit has already paid for itself. It comes with lots of plugs, probably enough to last me until cars become illegal. I will update this review if it turns out that I have any trouble with the plug. The instructions say that it is just supposed to be a temporary repair, but I am going to try my luck and see how long it lasts.

Good quality metal handles that fit in your hand good so you can apply the pressure needed to install a tire plug. The ream and plug holder part of the tools are good quality steel and not cheap junk. Starting in the mid 80’s working for GoodYear tire and rubber company shops I know how to plug tires and I know what good tools are! This is the good stuff you are looking for to keep in your car or truck! I highly recommend this kit to anyone that is able to do the work of plugging their own tire to get them out of a jam.

Calidad australiana

Great tire repair kit, a bit on the pricey side, but it comes with everything you need and proper quality tools, unlike most of the cheap kits you can buy at the various auto stores. The case alone is worth the extra money! Highly recommend for anyone who is into backcountry exploring or using their vehicles for work purposes (construction sites, oil field services, etc) where your chances of getting a flat are fairly high due to the debris/quality of the roads.

Sehr gute Qualität. Top

Very nice and solid product recommend to anyone

afortunadamente no le e usado pero esta muy completo y buena calidad