2Pcs PCIe NVMe M.2 2280 SSD Heatsinks Cooler Screwdriver Kit | with Mounting Screws

Easy installation and gets the job done quick.

If you're building PCs with used parts, these are a neccessity. They look good, fit well and are built well and don't strip as long as your not tightening them like a gorilla. Works with Machinist, MSI, Gigabyte and Asus boards. Keeps temperatures down. I didn't use the included rubber bands because they are going to rot and break so I dug into my O-ring kit and used O-rings which will take longer to break down. Nice low profile so if your SSD is under your GPU it will still fit behind it and not hit the GPU.

Works as intended, I do wish the rubber bands are black to match the heatsink.

Has a low-profile heatsink of aluminum, sized for a 2280 M.2 SSD. Plenty of spacers and screws and a great little phillips screwdriver (magnetized) to install those little SSD screws. Has silicone thermal pads to conduct heat to the heatsink. Even has little rubber bands to hold the heatsink to the SSD (even though they all broke when trying to wrap around the assembly). Everything was x2, so I have spares for future SSD's. Good Value for the $

such a good bargain. two sets of heat sinks for $7....can't beat that. I wasn't sure if it would be any good but I figured what the heck and give it a try. I put it on my m.2 gen4 samsung and ran some tests. running some speed tests of 5 iterations of 32GB read/write I was getting 69 degrees stock and with the heat sink I got 63 degree so I dropped temps by 6 degrees under heavy use. Very easy to install and the, don't know how long the rubber band will last but so far so good. Its nice that it came with screws also cause I really needed them.

Perfect for laptops!

I was short on screws for mounting an M.2 SSD, and ended up with this kit instead of just screws - because a little extra heat sink on recent large SDDs is never a bad idea. The blue heat transfer sticky pad is not that sticky, but it does not need to be due to the bands; and might save you if you apply it wrong. It's not a disaster to take it off and reapply. This kit does not dissipate heat from the back side of the SSD, but that is likely not needed in many cases unless you have an unusual build or possibly a hot console. I used both sets, would order this again.

I ordered this primarily for hold down screws for an M.2 NVMe drive, but for the great low price also got some spare parts. The heatsink and thermal pads fit nice, keep the temperatures down (which is important with NVMe SSDs for drive longevity) and the whole kit was worth every penny.

Fait un très bon travail, et dissipe très bien la chaleur.

Bought two pieces for Samsung 970 Evo Plus 1TB and P1 1TB. It is very easy to install, and it comes with small screw ( this screws are rare to find!). The maximum temperature for 970 Evo is dropped from 80'C to 62'C in my test before and after with heat sink. for P1, it is dropped from 65'c to 50'c. Very impressive.

I ordered these SSD heatsinks because they were cost-effective and low-profile. Admittedly, these weren't my first choice, but I figured they would be fine for mid-range SSDs and potentially fit in my laptops. I am glad I got them because they worked far better than I had hoped. Their cooling was more than adequate inside a mini-PC and desktop. An easy 10C to 20C drop in maximum tempurature. Sadly, they were too tall for the laptops I had. These will work with dual-sided 4TB and 8TB SSDs. The only downside is that both thermal pads are the same thickness. Some of my SSDs had uneven chip heights and required more than one thickness for proper contact.

According to Crystal Disk, the drive is operating at 6-7 deg Celsius cooler than before at idle (In a Desktop case), which is what I expected. The adhesive layer stuck well to the SSD and heat sink, but the elastics were not the right size. I needed to double-up the elastic to do anything. I didn't need the screws, but now I have some spares.

Be aware that the 2-pack only doubles the heat sink and thermal pad, and not the screw package. I bought this because my system (early SSD laptop) has tight clearances and pretty much none of the bottom U-shaped flange heat sink units would work - the screws attaching the flange to the heat sink would rub against the neighbouring components. Most of the SSDs with heat sink included tend to be a little too tall, and because the original 80 GB SSD didn't put out as much heat, I had to add a heat sink. The heat sink is rather low profile, which I needed. Not happy about the rubber bands, which I expect will fail over time with heat exposure. I might end up epoxying a few dots between the thermal pad and the heat sink and then cut & epoxy some tiny bits of the thermal pad to the top to try to hold it in place against the other side of the laptop - not great if the laptop gets dropped, but it beats the heat sink moving around.