MuHize Micro2 Fuse Taps - Upgraded RV Camper & Car 12V ATR Add-a-Circuit Adapter, 5 Pack 5A Fuses, Dual-Slot Design for Safe Circuit Expansion

The Mirco2 version Works on 2017 Hyundai Elantra engine compartment fuse box. You have to be careful that there is enough clearance in the direction you need. I used 2 taps, and part of a fuse, to change the power socket from Ignition controlled to Always on. I used tap #1 to get always on power from an unused slot. On Tap #2, because of the pigtail direction that was unblocked inside the fuse box, I had to jumper the pig tail to the power lead (left the fuses out, since there was one on Tap #1). I cut open a fuse in order to take the lead from one side and bent it into a U to jumper the two slots, then covered with electrical tape. Joined Tap #1 to Tap #2, and viola! Always on power socket. The leads on the included fuses were too wide to fit into the Tap. You would have to file them down to get them to fit. The fuses in the car fit fine. Also, two fuses would be a tight fit. The ones included had a wing on the housing above/below the amp number. That kept two from seating nicely. You would have to remove the plastic (cut or file off) in order to get 2 fuses to seat. The metal portion of the fuses seems to be aluminum, and easy to file and bend.

Bought these for my dash cam install. Been perfectly fine for YEARS now.

As advertised. Works

si.ple to install. works as advertised.

These fit perfectly in my 2015 Ford Fusion Energi. The fuses are a little tight in the slot, but easy to seat and remove with some needle nose pliers. I used them to hardwire my dashcam to ACC and Battery. I also hooked up my radar detector to ACC. I used the bolts that hold the OBD port for ground. You can use the fuse diagram that’s in the glovebox on Ford vehicles to determine which fuse you can tap into for ACC or Battery.

Purchased these for a dashcam install in my F150 using micro2 fuses. Seem very well made and worked great. Relies on you crimping the power wire into the fuse holder which is easy enough. Fuse holder end doesn’t specify which plug is for the original fuse and the accessory fuse which you need if they’re different amps. Had to look that up. (Original fuse goes in the plug closest to the fuse tap itself.). I only needed two of these, but for the price it’s great you get more than that. I’d recommend!

These fuse adapters are useful for a variety of vehicle electrical projects. Helps keep the installation clean and allows you to tap into a specific circuit such as the ACC power that's only on when the car is on. The pre-crimped wire splice makes for quick work. Great product!

Wiring kit for my dash cam included the wrong tap (I miss the old days when there weren't so many choices) so added these. It (1 needed of 5) worked and camera install was fairly straightforward from there.

Used on my truck for lights I added and I am fussy on how wiring is done I don't want problems down the road. This is a very clean and neat way to get job done without damaging any wires

The listing stated it is a micro2 blade fuse tap. When item arrived, the label on the packaging also started that its micro2 blade fuse tap but the actual item is a mini blade fuse tap. Disappointing that such an error can occur.

Great value, appear to be of good quality.

just what the doctor ordered works great

Purchased these fuse taps to wire in a dash cam. Previous fuse taps from Amazon have worked very well. These, however, were junk. The fuses that came with them (5A) would only go into the slots with severe force. To remove a fuse took brute force with a pair of needle nose pliers and actually tore a fuse in half before it came out. Ridiculous. Ended up throwing them out and finding a different brand. You get what you pay for.