DC-DC Stabilizer, 9V-36V to 12V Boost Buck Converter 5A 60W Waterproof Auto Step Up Down Voltage Regulator 12V Volt Transformer for Car Audio Solar Power System LCD Television LED Display Screen

Works awesome! My application requires close to 12 volts with the input voltage varying from 11.5 - 14 volts. This does the trick holding the output voltage at exactly 12.5 volts across an even larger input voltage range than I require. Admittedly, I would have been fine with the 3 amp version but chose the 5 amp to provide additional current capacity. I am drawing 1.7 amps continuous and it does not even get warm to the touch.

Worked perfectly. I had a long run of low voltage landscape wire driving my LED accent lights. The voltage inevitably drops over distance and the lights stop working after about 100ft. I installed this boost there and it bumped the voltage back up to 12.5v and helped drive the remaining 75ft of LED lights. Perfect solution.

I used this for a step-down voltage 5v output on a portable ham radio setup for POTA since November. Everything else required 12v, the tuner required 5v so I added this in line for its power. Seemed to work well. Yesterday the device failed spectacularly. Sudden "pop" noise, smoke, and even flame for a couple of seconds where the case had split. I had to evacuate the car until the smoke had dissipated. Glad I was there when it happened. Definitely done with these things, I will replace those I'm running at home as well. I can't trust them.

Cannot attest to it boosting 9v to 12v. It does buck (regulate) 14.5v down to 13.2v. Solved a problem with security cameras occasionally shutting down do to high a input voltage.

The LED strip lighting I wanted to install in my RV came with a transformer that converts 120VAC to 12VDC. But I wanted to wire the LED strips directly into my RV's 12V system. The problem here is that the LEDs are designed to function within a very narrow voltage range. The transformer provides this, but the output of RV batteries generally ranges from 11.5 - 14.4VDC, depending on SOC (State Of Charge). This problem is what gadgets like the DROK unit are designed for. With the input side of my DROK wired to the battery (through a fuse of course), I'm now seeing a very steady 12.2VDC on the DROK's output, no matter what the battery's SOC, and the two LED strips, wired in parallel to the output, perform flawlessly. Some reviewers have complained of the DROK unit overheating, and since it is only rated to 5 amps, or 60 watts, this could happen if devices that draw more than 60 watts total are connected to the output, or if there is a short circuit on the output side. My two 16' LED strips draw about 2 amps total, and after running them for several hours the DROK was only slightly warm. There is no heat sink with the DROK unit which is one reason why pushing the output rating could lead to serious overheating. For devices that demand more power you might consider the Ekylin Car Voltage Stabilizer model C121212 which is rated to 12 amps (144 watts), and is encased in a robust heat sink. NOTE: Regardless of which voltage stabilizer you are using, always wire the "+" lead on the input side of the unit through an appropriately rated fuse before connecting to the battery. Here's a link to the Ekylin 12 amp unit, fyi: https://www.amazon.com/Voltage-Stabilizer-Protector-Regulator-DC10-36V/dp/B08BRN3R5Y/ref=sxin_16_pa_sp_search_thematic_sspa?content-id=amzn1.sym.afd9c6b4-b179-4d6a-8ad1-7056a39c01ab%3Aamzn1.sym.afd9c6b4-b179-4d6a-8ad1-7056a39c01ab&crid=336PXO3ER7L7N&cv_ct_cx=dc%2Bdc%2Bvoltage%2Bstabilizer&keywords=dc%2Bdc%2Bvoltage%2Bstabilizer&pd_rd_i=B06Y5JHZG2&pd_rd_r=3036ce29-0c68-4c42-b56e-893bc9244a9e&pd_rd_w=oeyf1&pd_rd_wg=kRW30&pf_rd_p=afd9c6b4-b179-4d6a-8ad1-7056a39c01ab&pf_rd_r=W9GPWKJM08ZP8D58BZA4&qid=1695316652&s=industrial&sbo=RZvfv%2F%2FHxDF%2BO5021pAnSA%3D%3D&sprefix=dc%2Bdc%2Bvoltage%2Bstabilizer%2Cindustrial%2C175&sr=1-2-2b34d040-5c83-4b7f-ba01-15975dfb8828-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9zZWFyY2hfdGhlbWF0aWM&th=1

Worked great,

Great!

This DC to DC converter supplies 12v to my Eversecu Mod:ES-AHD-BGZ5 "HD Analog IR PTZ Dome Camera", mounted 80 feet up on a tower, So it's a big deal to replace when it fails. This is the second 5A, 60 watt unit to fail in 12 months. The first one destroyed the camera it supplied by passing 34vdc to the cameras 12v input. This time I was lucky, the camera survived, but there is still the issue of accessing it to replace it, 80 feet up the tower. I thought I'd give Drok one more try since I am happy with a different one of their products. So I bought a "F36W12V10A5L", 9V-36V in 12V 10A out model and it failed in 20 minutes, before I could even raise it up on the tower. @ $27 I expected longer service life especially with such a minimal 600ma load. Meanwhile my security system is down until a replacement arrives(next week, I'm told)

Bought this August '24 to supply a stable voltage to a MaxxAir Deluxe fan in my motorhome which pulls a maximum of 4A. Worked great..........for about 3 weeks in the 10 months it was installed and used. Now there is no output.

Easy install and works as advertised

This DROK DC Stabilizer is one of 2 main fixes for the dreaded MaxxFan green light beep and failure. The MaxxFan is the Best and Worst RV fan in the industry. When working, it is without a doubt the best RV fan with the most air movement, quietest operation, and low amp draw of the various options out there. But it suffers from 2 manufacturing fatal flaws that have been well documented by many who have suffered the fan failure. The first flaw is the circuit board not being waterproof, and living below a vent cap that can allow outside water onto the board, or inside condensation to drip onto the board. The second flaw is the electronic components used that are extremely sensitive to voltages over 13 volts or so. This is problematic as many RVs see voltages up to 14 to 14.5 volts when receiving charge from a generator, a tow vehicle, or a solar system. So having read numerous accounts of fan failures, and methods to correct the problem, I went in search of a DC voltage regulator. This one received good reviews, was well priced, and was also used by other fixing the same issue with their own MaxxFans. I installed this voltage regulator after having to replace my failed circuit board, in the hope that this permanently solves one of the problems. I bench tested this unit before installing it, as shown in the photo, using a portable lithium battery that provided 13.3 volts output. This Autoutlet regulator held the through voltage to a constant 12.2 volts. After installation, I again tested it once connected to my RV 12 volt system, which on shore power with the battery charger active was showing over 13 volts. This regulator did a great job of holding it to 12.2 volts installed. To protect the circuit board from problem #1 (moisture) I also coated top and bottom with thin coat of GE Silicone Supreme (neutral curing silicone sealant). I'm hoping these two remedies will keep my MaxxFan operating for many more years to come, hopefully with no more flashing-green-lights-of-death. I can't speak to longevity of this voltage regulator yet as it's only been in for a few months of operation, but so far it has helped the fan work flawlessly, thru all 10 speeds, in forward and reverse, as it is meant to operate. If you're looking for a reliable Voltage regulation option, I can highly recommend this Autoutlet device and the company selling it. Check out the attached photos for visuals of how I mounted it, using hot melt glue, into the outer frame of the fan. This caused no problems with clearance even in the low profile roof of our little Coachmen Apex Nano trailer.

Same story as others, bought for maxxair fan fix. 14V going in, less than 1V coming out. Waste of plastic.

Well I was having trouble with my Maxxair fan cutting out and not running. I spend days phoning rv dealerships to find out what I could do to fix the problem of the fan from stopping on its own. After calling the manufacturer of the camper fan I was sent a new circuit board, which didn’t fit the problem. Then I bought a controller panel which didn’t fit it. Company sent me a new controller again and a new motor. Fan worked for a couple minutes and shut off. Went onto Facebook and found that other people were having the same problem. The fix was this fantastic peace of electronics. Once installed the fan has been working ever since. If your having the same problem buy one and things will be up and running in no time.