SUZCO 13 Points Truck Bed Stake Pockets Tie-Down Anchors Set Side Wall Cargo Anchor Fits 07-19 Chevy Silverado I 07-19 GMC Sierra I 07-19 Chevy Colorado I 07-19 GMC Canyon - 1,000 lbs

Works great and very easy to install. Nice to have extra tie down locations and well worth the money.

You can’t never have too many tie downs. Take your time installing the first couple of them; not a very steep learning curve. Definitely pull on the anchor as you hand snug the bolt and later use a ratchet wrench to tighten the bolt if you want to keep your sanity. I’ve only used them with light loads so far but they se em pretty sturdy. Would buy again.

These fit all the 13 factory tie down anchor holes in my 2021 Colorado 6' bed with LINEX spray in liner. They were pretty easy to install even for a 66 year old. After installing in hole turn bolt 1/4 turn. Tilt the hook out and you can look in the seam and see the retention plate is where it should be. I kept some slight downward tension on the hook and start tightening. It will draw the hook into the hole. I did not have a 12mm ratcheting box end wrench but a 1/2" ratcheting box in will do and makes the install much faster and less aggravating. As some others I do not care for the silver bolts so I painted them a couple times with a small kids paint brush and some satin black Rustoleum paint. Looks great and will keep the bolts from rusting. The bolts are strong but will rust. It is a low grade stainless steel. I also added a SMALL drop of anti sieze to the bolt for possible future removal. HaHa that will never happen. Overall a great product at a great price.

I installed a set of these on my 2019 Colorado. The first one took me a couple of minutes to figure out how to install it. Once I learned the trick the rest went in quickly. First, make sure that the bolt threads easily onto the backing plate. Have backing plate threaded onto the bolt a few thread but still able to spin freely. Insert into the hole in th truck bed and push firmly against bed with one hand. with two finger of the other hand rotate the bolt 90 degrees and then pull the anchor away from the bed. If the backing plate had rotated 90 degrees it will catch on the bed. Continue to turn the bolt while keeping tension on the anchor. When you can no longer turn the bolt with your fingers tighten it up with a box end wrench. I didn't install one in the center hole in the front of the bed as it protrudes past the bed rail. If you put some piece of cargo into the bed and slide it forward it will not rest on the bed rail if one of these anchors is in that center hole.

Purchased and installed the 13 pack into a 2015 Chevy SIlverado with Rhino Lining sprayed. This was great as the stock hole covers wouldn't stay in and these fit perfectly finishing it off as well as useful. I made sure that the bolt turned freely before attempting to install, as one I had was a little rough. To take these out you need to be delicate or you will loose the back plate. Seated the tie down gave it a little turn and pulled the bolt while tightening and then snugged up with wrench. Video is just a quick walk through of installing one of them. Simple install.

Loved these, they were easy to install and you get all 13 to do the whole bed so I can have options to where I can tie down stuff to, great value and they are very strong and sturdy and cone with gaskets so no water gets behind them

Easy to install if you pay attention and only loosen the bolt far enough to rotate the back plate 90 degrees to install. Any further and you risk dropping the back plate down inside the bed wall. Nice foam gasket to seal up the bed wall. Look factory when installed. Description says they fit 2007 to 2021 Chevy/GMC. I installed on a 2022 GMC 2500 HD and they fit perfectly.

These are simple tie-downs, and I'm satisfied with them--they do exactly what I want. They are not that difficult to install, but I had to install about three before I got a smooth workflow. Getting the backplate perfectly perpendicular to the outer face requires some attention to detail. The included wrench is junk--just throw it away and use a real wrench. The nine tie-downs in this package is the exact number of openings in my Silverado.