HitLights Waterproof LED Strip Lights Kit, RGB Color Changing Pre-Cut 4FT

While it is perfectly possible and sometimes preferable to simply purchase a large strand of LEDs, cut them to length, and attach the necessary connectors, I had plenty of room in my computer case and did not feel like spending extra on ordering additional adapters, so managed to make these work almost flawlessly. By utilizing an adapter to plug into molex power (purchased separately from Amazon and included in a previous review), I was able to power these directly inside my case. These are also perfect for those individuals that do not have the knowledge about cutting there own LED strands or are simply uncomfortable doing so. Additionally, the colors can be changed or even various actions performed by the lights with the included remote! I found this feature particularly useful as I simply was not sure how everything would look when complete and this gave me the flexibility that I needed. Additionally, all the connectors were already included to connect each of the four, one foot strands of RGB lights together, meaning no other purchases unless the molex adapter is needed as mentioned earlier. I highly recommend these items as they worked great, however, I want to also mention some considerations while installing this item: 1. Each strand contains it's own double sided tape to be able to affix it directly to the items desired. Even though I put it into a brand new case, I did have some slight difficulty keeping the adhesive sticking in some areas, though, admittedly, I did not attempt to wipe down the surface ahead of time. They also include additional adapters that can be used to mount the LEDs that also use double sided tape should that be necessary. 2. Before installing, it is a good idea to attach all the strands together and test them out. I ran into an issue in which I accidentally installed a connector or two backwards (which is possible) and resulted in some strands not working initially. Again, this is more on me than on a problem with the manufacturer. Simply keep an eye on how each strand is connected as there is a little arrow on one side to show the correct positioning. Doing so will save some headaches later! 3. As the remote is IR, a direct line of sight is likely necessary in order to use the remote. Keep this in mind when installing, especially as I did inside a computer case. Formulating a plan as to how this will be installed will allow you to change the lights on the fly without dismantling wherever these are installed. (For me, I actually put the receiver in an open fan port on the top of my pc case. It allows me to change the color when I want and is hidden behind a grill, so is not even remotely visible to others). In the end, I am perfectly happy with these and will likely utilize these or another Hitlights product based off of my experience when I have a need to use them in the future, in computer cases, or throughout the house.

I purchased these LED strips to accent a new PC I built recently, and they have done an excellent job so far. I did have a minor issue with the adhesive not holding on vertical surfaces, so I contacted the seller about the issue. They were very easy to work with and helped me get the issue resolved without any hassle on my part. Overall, 5/5 would purchase again. Pros: The strips are sized perfectly for adding accent light to a PC. Having 4 one foot sections is way easier to work with than trying to use a single long strip or building/soldering them yourself. I tried the remote control through the glass side panel of my case and it worked perfectly. I currently have the lights plugged into the Aura RGB header on the motherboard to control them that way. This also works without issue. This kit includes everything you would need to wire a PC up for lighting including enough extension cables to wire everything in so it looks nice. Cons: As I said, I had a minor issue with the lights not holding on vertical surfaces. This was solved by using some double sided mounting tape, which has held well. I am not entirely sold on using the included clips. The adhesive does seem stronger, but it created a 'speed bump' looking bubble over where the clip was, causing a part of the strip itself to lose contact with the case. These bumps were always the first place to lose their grip before I used the double sided tape. Other: I also have some LED lights around my desk that has been installed for a while. It is the same type that is sold in 15 ft rolls that you can find all over on Amazon. The wiring for the LED strips I already had and these were different, so that when I tried to wire them into a single controller and power supply the blue and green channels were reversed. So if I had full green on my old LED's it would have full blue on the new ones inside the case. This isn't something that the seller can control, nor is it something I thought to ask before purchasing, but it is something to consider. Oddly enough, because only the blue and green channels are reversed, full red works fine. I was able to solder in a wire a crossover for the blue and green where the new LEDS are wired in and after that the colors matched without issue.

I ordered this to put behind my 52" flatscreen TV for some 'mood lighting'. I am very happy with it. The instructions are vague and printed on a tiny slip of paper, so I can see how some people might have a problem. But it you just look at it rationally it's pretty easy to figure out. The light strips mounted easily and, after a week, they are still stuck solid to back of my monitor. The colors are bright and look fantastic. If I had one piece of advice I would say map out how you are going to install them before you buy. This kit is designed to have all 4 strips set in a line and the extensions are only about a foot long. If your layout demands that the strips go in different directions or you will need to set them further apart you will need to order those pieces separately. I could have benefited from being able to split them into two directions but I still got it to work without too much compromise. I wish you could control some of the effects. It would be nice to be able to control the rate of the strobe and fade but you can't. Plus, the instructions say you have 8 levels of fade up/down but on most of the colors you can only see a few different levels. When I first set it up 2 of the strips did not come on so I sent HItLights an email. They responded within a few hours with a suggestion that worked so I am happy so far with the support. **Turn the plug going into the non-working strip around.. I guess it matters even though they are not really marked in any way.

Perfect for a multiple aquarium setup. Have 3 five gallon aquariums with homemade plexiglass tops. Used these strips on top, not inside. Used clear double-sided tape to mount them facing down. Used the extension cable between sets which allows the plexiglass tops to open easily. Got the waterproof design. Excellent brightness. Easy to install and work with. High quality. Love the remote ability.

Very easy to install. I placed all four strips on a narrow piece of wood and placed it behind my 48" aquarium. Perfect brightness and the range of color options was a bonus for me. When the day comes that I get another tank, I'll definitely be getting another set.

Purpose: bought light strip for small home server rack. There were alot of reviews warning about the adhesive, but I took the risk. First everybody is right, even though I cleaned the area, the adhesive did not stick. So I went and bought some two sided tape and so far so good. Second issue: the adapters that join the lights do not stay connected very well. There is no locking clip or anything. You just insert Male ends to female ends. As I tried to install the lights, a strip would fall off and disconnect constantly. I ended up having to use electrical tape to keep the strands together. Once I got the strips installed, with two sided tape and electrical tape. I grabbed the remote and felt like Chevy Chase in the movie, National Lampoons Christmas, when he plugged in the lights and that feeling of accomplishment. Of course the first time they didnt work because I got the wrong polarity on one of the strands 2nd time was the charm though. The remote worked great as long as the IR sensor was in view. They were very bright and you can change colors and change light brightness. One last thing, everytime I plugged in the power adapter I noticed a spark. At first I thought it was a grounding issue but I tested that and I found no issue with my APC surge protector. So I am a little wary about it but since these Led strips are low voltage I didnt seem it being to much of an issue. If the company would improve the connectors and better adhesive it wouldn't be a bad product, but for the price I guess they will do. UPDATE: Their customer service contacted me and stated that they are working on improving the 3M tape on their product. They also apologized for the trouble I had gone through and gave me a full refund. Because of their friend customer service I will give them another star for that.

As Good as the first set useful for Pachinko Machine Upgrade in Lighting on Classic 70's Machines!!!!

Great quality and the colors are awesome and waterproof , stable, fun , visibility is very nice would recommend for sure