EPEVER MPPT 10A Solar Charge Controller 12V/24V Auto, Max Input 100V,Solar Panel Charge Controller Regulator with LCD Display Tracer1210AN
Description
- ☆We have stock in the US, can give you a fast delivery and the best service.Advanced MPPT technology, with efficiency no less than 99.5%. ☆Ultra-fast tracking speed and guaranteed tracking efficiency, it can accurate recognition and tracking of multiple-peaks maximum power point, increasing the ratio of energy utilization in the solar system by 10%-30% compared with a PWM charging method. ☆Network type MPPT solar charge controller with RS-485 communication bus interface and Modbus communication protocol, it is available to meet various communication requirements in different situations. ☆Supports PC(ONLY Windows) monitors and Remote Meter MT50 for real-time data viewing and parameter setting. ☆Please read the instruction manual carefully or consult customer service to avoid damage to the new controller due to improper operation.
Size:Tracer1210AN EPEVER Network Type MPPT Solar Charge Controller 10A Tracer1210AN 12V/24V Auto, Max Input 100V with LCD Display for Lead-Acid and Lithium Batteries We have stock in the US, can give you a better service and fast delivery.Feature: Rated charge current:10A Max.PV input power: 12V/130W,24V/260W (12V/24V Auto Work) Battery voltage range: 8V~32V Max.PV open circuit voltage: 100VDC Ultra-fast tracking speed and guaranteed tracking efficiency, advanced MPPT technology, with efficiency no less than 99.5% Network type MPPT solar charge controller with RS-485 communication bus interface and Modbus communication protocol, it is available to meet various communication requirements in different situations Wide MPPT operating voltage range Multiple load work mode:manual mode, light control, dual time setting and adjustment control mode Terminal: 12AWG(4mm2 ) Recommended cable:12AWG(4mm2) Dimension:172x139x44mm Net weight:0.6kg Electronic protections : PV short circuit protection PV reverse polarity protection Battery over voltage protection Battery over discharge protection Battery reverse polarity protection Load overload protection Attention: The flooded battery must be well ventilated to avoid explosion Please make sure that the positive and negative terminals of each component are wired correctly Package List: 1 x Tracer 1210AN Solar Charging Controller 1xTemperature sensor（Model:RT-MF58R47K3.81A） 1 x User Manual(English)
Reviews
D**O
Warning temperature limits do not work!
So I got the one to charge lithium batteries. Got the software and installed it, that ran fine. However, when I set the default temp limits (charge should cut off if temp falls under 0F, load should cut off at 20F), they do not seem to work. I have my rig outside and it reports solar, battery, load voltages and amps as well as battery and case temperature with the included sensor. The sensor works fine and reports temps correctly. However, I have had a couple days where the battery temp was under freezing and yet the controller was charging the battery. Also, there have been several nights with temps below 20F and yet the unit kept the load powered. This can't possibly be good for the battery, I am monitoring its health at the moment.So word of warning, do not rely on the charge controller parameters for temperature, for some reason it completely ignores them. I can't speak for the high temp cutoffs, but I fear those may not work either.The only reason why I'm not returning it and marking it with two stars instead of one is that my rig will eventually be deployed in a climate that will very rarely see temps below freezing, so for that it may be ok. But, I may have to purchase a new battery.Other than that, the unit works well and the interface specs were nicely published and allowed me to write my own monitoring software. There are a couple of glitches with the registers, not sure if it's the firmware in the unit (calculating power) but I was able to get around that one.
S**E
So far so good.
Arrived on time and as described. Directions for installation were clear. I did a temporary instal as I have not decided on where the permanent placement will be on my boat yet. I have two 100w panels connected and it appears to be working as described. It took about five minutes with the directions to program for my AGM batteries. I will know more after a year of use after permanent instal but for now five stars, can’t find a flaw.
Common Questions
Trustpilot
2 weeks ago
2 weeks ago
